Search results

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. team117

    Want to Sell Makita ea7900

    New makita ea 7900 prz2 wrap handle. $900 pho shipped to the lower 48.
  2. team117

    Sold Makita ea4300

    New makita ea 4300f with 16" bar. $325 shipped to the lower 48.
  3. team117

    Want to Sell Makita ea6100

    New makita ea 6100p With 20” bar. $600 shipped to the lower 48.
  4. team117

    Want to Sell Makita Ea5000

    New makita ea5000p with 18”bar. 500 shipped to the lower 48.
  5. team117

    Sold NIB STIHL MS 440

    I purchased the saw from a fellow member in 2018. $1200 pho shipped to the lower 48.
  6. team117

    NY GTG 10/12/19

    Well better late than never. Located at our shop in Wolcott, NY we will have product demos for Makita OPE and split fire log splitters. If you bring a saw to cut wood please wear proper safety equipment. The address is 5674 State Route 89, Wolcott, NY 14590.
  7. team117

    Want to Buy Ms440

    Looking for a good low hour saw.
  8. team117

    Want to Trade Ms660

    Vary low use ms660 in like new condition. Looking to trade for a 440 or 461 in equal condition. Will sell as pho for $950 shipped to the lower 48.
  9. team117

    Sold Ms362 cm

    For sale is my ms362. The timing is advanced 1/3 of key. The muffler has been matched to the port and opened up slightly. 425 pho shipped to the lower 48. Add 25$ if you would like the 20" bar and chain.
  10. team117

    Sold ms440

    Intake and exhaust are ported. The upper transfers were left alone. Timing is advanced 1/3 of a key. There is epoxy in the intake. All oem except dual port exhaust cover. Pressure and vac tested. 425 pho plus shipping.
  11. team117

    Sold ms 361

    The saw has the oem cylinder, meteor piston and caber rings. The base gasket was replaced with thinner one than oem. The carb was modified to a larger venturi walbaro. The intake and exhaust ports where smoothed out. The muffler baffle was removed. The plactics are faded and I had to weld the...
  12. team117

    440 b starting problem

    I have a 440 b skidder that has developed a problem in the steering system. If you open the bleed port for the steering system and turn the wheel full right it will crank over and start fine. If you just try to start it normally it will barely turn over and if it can turn over fast enough to...
  13. team117

    Sold stihl 32" bar

    this bar has made one cut. I don't need a bar this size. 85$ shipped. 100$ for the b&c shipped. lower 48 only.
  14. team117

    Sold Ms660

    New, never cut wood. $1,250 pho shipped to the lower 48.
  15. team117

    Want to Sell Husqvarna bars

    The Oregon and husqvarna bars are a different size mount than the Carlton. 20" bars 45$ each.
  16. team117

    Sold Ms 361

    This ms 361c was ran at the dealer but never cut wood. $575 pho shipped to the lower 48.
  17. team117

    Sold Ms 261

    This saw is a standard carb model. The limiters have been removed. The strato divider has been removed. Timing advance, muffler modded. $450 pho shipped to the lower 48.
  18. team117

    Sold Stihl 361, 036, 441

    Ms 361 pho $365 shipped lower 48. Has sun fading on plastic but is not too bad. Only non OEM part is a meteor piston. Ms 441 pho $450 shipped lower 48. Stihl 036 pho $275 pho shipped lower 48. Also has meteor piston.
  19. team117

    Sold Ms441 $525

    $650 pho shipped.
  20. team117

    Want to Sell Stihl 036

    Great runner. Mild port work. Squish set at .021". $350 pho shipped to lower 48
Back
Top