Search results

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. davhul

    Want to Buy Stihl USG chain grinder

    I’m looking for a USG grinder. Thanks
  2. davhul

    Low compression on my new Stihl MS362

    The 5 compression test are null if they were using the wrong tester like stated. Post a vid. The problem could be a simple fix with a fresh set of eyes and ears.
  3. davhul

    Huztl Thinks They Should Have My Videos

    Stihl acquired zama years ago. That's about the time the price came down on zama for Stihl
  4. davhul

    FarmerTec Huztl MS660 Updated Build Kit - Build Thread

    I like around 2800. With the stiff huztl springs the chain won't creep til over 3500 I think.
  5. davhul

    FarmerTec Huztl MS660 Updated Build Kit - Build Thread

    It was. Out of 4 pumps 1 quit and bedford sent me another so I didn't have to wait. Thanks Bedford, Ireland sent me another no questions asked. When I put the pump on I put the worm on before I tighten the screws to help center the pump.
  6. davhul

    FarmerTec Huztl MS660 Updated Build Kit - Build Thread

    I noticed half way through my oiler quit. It was the pump. Already had a oem worm.
  7. davhul

    FarmerTec Huztl MS660 Updated Build Kit - Build Thread

    I have 2 running huztl cylinders and 1 with a meteor. The huztl's arn't round. And when I tore my first one down after only a couple tanks I could tell. The saw was still running fine but I wanted to upgrade the cylinder before I gave it away. The cylinder had a lot of high spots where...
  8. davhul

    FarmerTec Huztl MS660 Updated Build Kit - Build Thread

    I don't have a oem trigger to measure
  9. davhul

    FarmerTec Huztl MS660 Updated Build Kit - Build Thread

    I may have a oem to measure I'll see. Most of the time the master control switch needed to be shimmed on each end, Its to loose. A thick straw over the ends or I've even cut a strip off a leather glove to add slight outward pressure to the switch. Something else you can try.
  10. davhul

    FarmerTec Huztl MS660 Updated Build Kit - Build Thread

    On your oil pump I would look at the plastic worm gear also. The wire on mine would slip around then wouldn't pump. I would get a decomp plug coming. You don't want the possibility of the valve leaking. Squish on all 3 of mine had.023-.025 with the huztl cylinder and no gasket.
  11. davhul

    Huztl MS660

    This is some Fault Analysis info that might help someone determine what caused a failure. File was to large hope the zip works
  12. davhul

    Huztl MS660

    Thanks, I'll have to see if there's a mark on the rings to tell.
  13. davhul

    Huztl MS660

    How do you like them long term? I didnt look I heard there was different ones but didn't want to chance it. I actually like the softer rings and hope the saw lasts to wear them out.
  14. davhul

    Huztl MS660

    I'm with you here on the extra oil. I personally run 32:1 all the time for the extra lube for the bearings and the chrome cylinder I also keep the tune around 12,5-12,8k. I had 3 I built to gave to friends and 2 in which cuts wood everyday and are a year old now. The other guy cuts only...
  15. davhul

    Huztl MS660

    Here's a little Stihl 250.
  16. davhul

    Huztl MS660

    I've thought about another 440 kit also and get the 460 topend. But I still have another 660 kit sitting here in the box I need to assemble So maybe later. If you change your mind on a 660 it'll run a 36 ok. Phone died mid cut And 440 ran good also.
  17. davhul

    FarmerTec Huztl MS180/250 Complete Chainsaw Kit

    Are the needle bearings missing or are they trying to use a bushing now? I have a huztl ms180 topend and crank I was sent for testing for a unrelated problem. This one has a bearing and no up and down movement.
  18. davhul

    038 air filter

    I've heard that also with the AM ones. And only reved to 8,000 rpms. Wish I could ship you one from here and save you $. I can get one for about $30 with tax
  19. davhul

    Huztl MS660

    I was thinking the same thing. But I think very little reading went on. During that 156 pages of reading there would have been a comment or question way before now
Back
Top