Search results

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. KennyPete

    Want to Buy 192t CYLINDER

    I have a complete cylinder/piston/crank out of a 192t. PM me if you're interested.
  2. KennyPete

    Huztl MS660

    This pile of parts is finally looking like a saw. Waiting for a new clutch drum before I fire it up. The one they sent me was too tight. It measured .611 and the one off my stock 660 measures .630. Tried milling it out but those clutch drums are made of some pretty tough stuff, my carbide...
  3. KennyPete

    Sold 10mm Stihl 044 $450 shipped

    I picked this up at an auction last year. Only selling because I finished my ported 461 project and I don't need it. Has 150lbs compression, good runner. Pulls a 32" bar and chain with ease. Has a 066 air filter cover and a 440 handle, but otherwise it's an original 10mm saw. I haven't done...
  4. KennyPete

    Beware Husqvarna 350 cylinder kit from CustomChainsawParts on eBay

    I am going to throw a caber ring in it as someone suggested above and see if it will run.
  5. KennyPete

    Beware Husqvarna 350 cylinder kit from CustomChainsawParts on eBay

    I wasn't out here to smear, just saying buyer beware. I should have made them replace it when it showed up with casting flaws, that was my fault.
  6. KennyPete

    Beware Husqvarna 350 cylinder kit from CustomChainsawParts on eBay

    As you can see, other than some transfer from the ring there is nothing wrong with the cylinder (other than squish area being too large). I also included a pic of the solder I used to initially measure squish. It did not even touch the top of the cylinder with everything torqued to spec and no...
  7. KennyPete

    Beware Husqvarna 350 cylinder kit from CustomChainsawParts on eBay

    I purchased this kit to throw in a buddy's 350. When I received it, the port castings were rough so I cleaned them up a little with a dremel. Assembled as normal, no run, <90psi compression. Passed vacuum test. Took it apart. Removed base gasket and measured squish @ .032 - reassembled...
  8. KennyPete

    Huztl MS660

    I ordered one of these kits. Never sent me tracking info, but it showed up 3 weeks later. All parts are here and accounted for. I assembled the crankcase. Froze the crank, heated the case halves, and it went pretty smooth. Will update as I go.
  9. KennyPete

    Sold Jonsered 2095 - $550 shipped

    Sold!
  10. KennyPete

    Sold Jonsered 2095 - $550 shipped

    I bought this as part of a lot at an estate sale. The bad: It had a crack in the muffler, so I welded it shut. The pull rope was short so I replaced that as well. The chain brake does not function. It's a little ugly. The good: Strong runner. ~155psi compression. Runs/Cuts/Oils as it should...
  11. KennyPete

    Want to Buy 90cc saw

    I have a Jonsered 2095 for sale. 94cc, 20" bar and chain. Bought from an estate sale. Gave it a going over. Welded a crack in the muffler, replaced the rope. Starts/Runs/Cuts well. Sat around 155psi compression when I bought it. Asking $550 shipped.
  12. KennyPete

    Want to Sell Makita 6401 84cc Big Bore. **sold pending funds**

    Short on cash, will you take my second born? She doesnt eat much and is great for jobsite cleanup hahaha. Great saw, good luck with sale! I would buy it if I had the cash to blow
  13. KennyPete

    Want to Buy Stihl ms193tc ignition coil

    As the title states, looking for a 193tc ignition coil. Dealership wants $90.
  14. KennyPete

    Want to Sell Stihl 051 AV Make Offer need Gone NOW!!!!!!!!!

    This. If you're looking for that kind of money, you're better off on eBay. Maybe someone will go nuts over it, unlikely though.
  15. KennyPete

    Long term experience with Poulan Pro 5020?

    I bought one a few years back to keep at my camp (figuring if someone stole it I wasn't going to cry over a $189 saw.) I cut a couple cord a year with it, and the neighbors use it whenever they want. Honestly a decent cheap saw. I had two problems to date with that saw: 1.) My gas cap...
  16. KennyPete

    Want to Buy Stihl ms310 cylinder

    Pull the cylinder and use a helicoil.. I have fixed several cylinders with them, all of which still work to this day. Excellent $2 fix Sent from my A0001 using Tapatalk
  17. KennyPete

    Sold Husqvarna 266 - $200 + shipping

    Sorry for not replying sooner, my kid gave me a nasty cold that turned in to pneumonia. Compression is 140 Sent from my A0001 using Tapatalk
  18. KennyPete

    Sold Husqvarna 266 - $200 + shipping

    I took this on trade for an MS250. Saw was too heavy for its previous owner who is in his 70's. I traded him a MS250 straight up for it. Strong running saw, 20" bar and chain, needs cleaned up & new stickers if you want them. I will pull muffler and take pics & get compression numbers tomorrow...
  19. KennyPete

    Sold Husqvarna 272xp or 61/266/268

    I have a 266. Strong Runner, 20" bar & chain. $200+ shipping.
  20. KennyPete

    I saw it on Ebay/Craigslist

    If you need one for the collection.. http://akroncanton.craigslist.org/grd/5813957864.html
Back
Top