Search results

No its 1in threaded rod. Sent from my SM-G892A using Tapatalk

An update on the saw. It's now has a cross top end with a base gasket delete. I have it in my mill right now. I'm running my 36in bar. Cuts really well. Hoping to mill some more with it soon. Sent from my SM-G892A using Tapatalk

It could be your metering lever in the carb is off. There is a video somewhere how to adjust them. But people with the same symptoms as your saw say that's the problem. Edit I found this hope it helps

My guess would be yes to machining it down. Mines .022 inches with no base gasket. Sent from my SAMSUNG-SM-G890A using Tapatalk

I have a 3/4 wrap on my 461. And I really like it so far. Sent from my SAMSUNG-SM-G890A using Tapatalk

Fingers still crossed for an MS880 Sent from my SAMSUNG-SM-G890A using Tapatalk

I have another saw that's getting tested soon. Lol Sent from my SAMSUNG-SM-G890A using Tapatalk

Sorry the tank is perfect passed the tests with flying colors. Those numbers are for the engine. Sent from my SAMSUNG-SM-G890A using Tapatalk

I pressure and vacuum tested my HZ660. It looses 1 psi of pressure in 1min 30 sec and it looses 1 inHg in the same time. Is the exeptible? Sent from my SAMSUNG-SM-G890A using Tapatalk

Yep I just posted a picture of my filter showing exactly what you explained. Lol. I will have to get it fixed before I mess the saw up to bad. But first I'm pressure/vac testing it tomorrow hopefully. My mityvac is suppose to be here tomorrow Sent from my SAMSUNG-SM-G890A using Tapatalk

I think I found my problem. It's hard to tell in the picture but the filter is sitting at about a 60 degree angle up the back side of tank. The bottom of the picture is the verticle side of the tank where the handle is. Sent from my SAMSUNG-SM-G890A using Tapatalk

It appears my fuel line is oriented in the handle correctly. Next step is to look I the tank. Sent from my SAMSUNG-SM-G890A using Tapatalk

I usual do 2 cuts on the smaller stuff before fueling. Generally leaves me with about a 1/4 tank depending on all the variables. (But I was rushing that night should have slowed down some) I have learned my lesson about running out mid cut. Lol Sent from my SAMSUNG-SM-G890A using Tapatalk

The first time it happened the tank was almost empty and the second time happened at 3/4ish. I will look into the vent as well. I ordered a mityvac today so I can do pressure/vacuum tests on my saws. I keep building and rebuild more so it will be a wise investment for me.

Thanks I will have to give it a look. (The Tank is 3/4 full right now)

I know but I figured while I was there I would get one. Good to have a spare one kicking around if I decide not to use it.

That's what I was thinking. Fuel filter related. I might get an OE one tomorrow and a new plug. It's running a used NGK from my BB660 right now. Sent from my SAMSUNG-SM-G890A using Tapatalk

I milled some year old cherry with the HZ660 tonight. It did really good. I had 2 stall outs in the hourish I ran it. Not sure what it was about. It stalled like it ran out of fuel. But I would stand the saw up and it would restart. Not quite sure what's happening there. But I will investigate...

It's been a wet summer here. It has rained just about everyday this summer. Hope to get my sawmill done once we're are done with firewood. Then I will be working the saws. I have a timberframe shed I want to build next summer of everything works out. Sent from my SAMSUNG-SM-G890A using Tapatalk

Three tanks thru it so far. Some say to break them in the way you are going to run them. I'm going to fatten the tune up to 13000 and let it eat. Sent from my SAMSUNG-SM-G890A using Tapatalk