Search results

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. happysaws

    ACME Square Grind Chain Attachment

    I posted this in the WTB section quite a while ago, and received no responses, so here goes. Many years ago, my father aquired an old ACME circular saw blade sharpener. He has been looking for years for attachments for it, specifically the ACME chainsaw chain sharpener attachment. If anyone...
  2. happysaws

    Yamaha TTR 225 no power under load

    Super off topic here, but here goes. I got a 1999 Yamaha TTR225 a few months back, and I cannot get it to have power under load. So far, I've rebuilt the carb, replaced the fuel shut off valve, installed an E3 plug, and replaced the battery. I've even tried oversized carb jets, but those didn't...
  3. happysaws

    Want to Buy ACME Saw Chain Sharpener Attachment for Acme Grinder

    Many years ago, my father aquired an old ACME circular saw blade sharpener. He has been looking for years for attachments for it, specifically the ACME chainsaw chain sharpener attachment. If anyone has one of these, or knows where one may be, he would be very interested in buying it...
  4. happysaws

    Vocation Project for School (Forester/Arborist)

    I'm currently working on a research paper for school. It's considered a "vocation project", and the vocation that I've chosen to research is that of a forester (or arborist). Part of the paper requires that I send a short questionnaire to someone currently employed in the vocation, and ask...
  5. happysaws

    Stihl 041 Super Crank Seals Part Numbers

    Looking for part numbers for the Stihl 041 Super crank seals. Thanks!
  6. happysaws

    Stihl TS760AV Cut-off to Chainsaw Conversion

    I bought a Stihl TS760 cut-off concrete saw, it runs great. I would like to convert it to a chainsaw similar to the 076. Does the concrete saw have an oiler, or will I have to find an 076 oiler? Will 076 bar studs fit in the TS760? I'm sure I'll think of more questions, but this is all for...
  7. happysaws

    Remington Super 754 Problems

    I've got a Remington Super 754, I have cleaned and rebuilt the carb. It will start and idle well, and cut okay with a little smoke when the saw is held upright with the bar parallel to the ground. When the saw is running at WOT with the bar pointing towards the ground, the saw will run very...
  8. happysaws

    Vintage Lancaster Chainsaw (Five-60HL??)

    I acquired an old Lancaster Chainsaw, it is what I believe to be a Five-60HL. It has the 500 series West Bend engine, it runs and cuts good. So, the air filter(s) are little cylindrical wood-like things. They are on the front of the saw, right where all the sawdust accumulates. The saw runs WAY...
  9. happysaws

    Spark Plug Error Causes Saw to Run Lean?!?

    Okay...so I have an old Remington chainsaw that was running lean when cutting, even with the high idle screw set 3+ full turns out. I ruled out the following; *carburetor *fuel pickup *fuel lines *air filter *points (gap) *coil/condenser/flywheel magnets *condition of p/c etc... The saw would...
  10. happysaws

    Mityvac pressure test on old saws

    Has anybody ever used a Mityvac on an old saw that uses reed plates? I would like to vacuum/pressure test the crankcase on a few old saws, but I'm not sure how to do it, because the old saws use reed plates. There's no barb to connect a hose to for putting pressure/ vacuum in the crankcase...
  11. happysaws

    McCulloch SP125 decompression valve

    Will a new Stihl or Husqvarna decompression valve fit into a Mac 125? The one I have leaks when the saw is running. Any help is appreciated!
  12. happysaws

    Want to Buy Remington Super 660G sprocket

    I have a Remington Super 660 G chainsaw that runs great, but the sprocket is wore out. I'm looking for a new (or slightly used) sprocket, in either .404" or 7/16" pitch. If anybody has one or knows where I can get one, please let me know! Thanks much.
  13. happysaws

    Want to Buy McCulloch 125

    I'm looking to buy a running Mac 125 in good condition (preferably a CP125). Please PM pics and a price, thanks!
  14. happysaws

    Ignition Points Timing Question

    I've read how opening the ignition points on a chainsaw a few thousandths should slightly advance the timing, and in turn should make a saw have more high end rpm's, but will advancing the timing with the points make the coil overheat? I would like to try this with a few of my vintage saws, but...
  15. happysaws

    Want to Buy Remington PowerLite PL-6 crankcase

    Hey all, I'm new to this site and not sure how everything works, but I really would like to replace my cracked crankcase and get the saw running again. The part number is 64612. Thanks, Luke.
Back
Top