Search results

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. BonScott46

    Stihl 194t running pmm3

    Just bought a 194t that came with pmm3 semi chisel safety chain. Anybody know if there is a standard picco (low profile) full chisel in 0.43 gauge (1.1mm)?
  2. BonScott46

    Cutting birch in Sweden

    Been picking away at this job when it hasn’t been terrible weather. Cutting for a Danish customer that had a summer house in my area. 20+ trees between 12-24 inches came down. Logs cut to 3.1m. At first he wanted me to ring it up in 30cm (1 foot) rounds and then he was going to move it all to...
  3. BonScott46

    Logger Down-Helping costs you nothing.

    Hi guys, I saw yesterday on FB that Patrick Lacey had an unfortunate run in with a dirty rotten snag on the job and is currently laid up. From the sound of it it was pretty bad. He is not looking for donations so I figured I would take a cue from his buddy that posted on FB and try to get as...
  4. BonScott46

    Sold Jonsered XG (85cc) excellent condition 525USD shipped

    Jonsered XG (52mm, 85cc) in excellent condition. Same story as the XF that I posted. Piece missing from the front of the top cover near the muffler other than that in excellent condition. Paint is RED and very nice. Saw has been run more than the XF but still not much from the looks of it. Good...
  5. BonScott46

    Sold JONSERED XF (110cc) excellent condition 1050USD shipped

    Jonsered XF (56mm 110cc)in excellent condition. Came from a Swedish guy that has been cleaning out his collection for several years. The pictures tell the story on condition. Paint is RED and very nice. Excellent compression and saw fires on prime. I do not know a lot about these saws but I will...
  6. BonScott46

    Birch trunk covered in webbing

    I have a birch (betula pendula i think) in my backyard here in southeren Sweden, it is about 2.5-3ft on the stump. I noticed today that the trunk as far as I can see up to at least 30ft is covered in fine webbing that runs vertically. When you look up the trunk it almost looks as thought it is...
  7. BonScott46

    Sold ms462 with heat NLA

    Any interest in a new ms462 with heat PHO somewhere around 1400USD shipped from Sweden? These just showed up here and I figured I would see if anyone is interested, I can get 2 of them at this price.
  8. BonScott46

    ms361 muffler mod

    If you ain't done it already, do it. All I did was gill the side, four 3cm long cuts and opened them up. Hory sheet what a difference. Can't imagine what this thing would be like with a base gasket delete and a popup...
  9. BonScott46

    Husqvarna cylinder ID

    Anyone know what cylinder this is? 266? Thanks.
  10. BonScott46

    Want to Buy Tsumura Light an Tough 24'' .063

    New or like new condition. Will be shipping to California not Sweden. Thanks.
  11. BonScott46

    Autotune / M-tronic sparkplug color

    I don't own either of these types of saws but I was curious as to how the plugs look on these saws since they are supposed to be running on the verge of too lean. Pics would be great if anybody has some.
  12. BonScott46

    JB Weld Plastic any good?

    Have a relatively minor crack where the rear handle joins the footpad on an 044 and want to stop it from getting any worse. Is JB Plastic Weld any good or is there something better at around the same price? I was also thinking I would try and fill in under the footpad to reinforce it. Has...
  13. BonScott46

    Bar adapters

    Any adapters for large husky to small husky or does the oiling not line up?
  14. BonScott46

    044 muffler mod

    Not much of a thread but I am looking to mod my 044 muffler it has the divider with the 3 big holes, does it go to pry that out or does one need to cut it out? Also, behind the divider is a metal box with smaller holes surrounding the inlet to the muffler. Is it best to cut that out completely...
  15. BonScott46

    Inner bar plate removal metal tag Stihl 036

    Have a metal tag 036 with the inner plate that has no screw holding it on but instead grips the bar studs. Workshop manual only shows the screw type inner plate. Do you just pry it off? I tried some but I don't want to end up bending it if there is another way.
  16. BonScott46

    Don't judge a book by its cover

    Came up on this metal tag 036 Swedish ebay and thought I would share. Underneath a thick gooey layer of dried vegetabe oil, the pictures do not do the goo justice, is a 20+ year old saw in excellent condition. I thought the cylinder was an aftermarket when looking at it with the top cover on...
  17. BonScott46

    Stihl 036 Quickstop

    Looking at going after a Stihl 036 Quickstop, seller says the quickstop is nonfunctional and is actually calling it Quickstart. I am not at all familiar with this feature besides that it engages the chain break when you let go of the tank handle. Does the normal chainbreak function work without...
  18. BonScott46

    Husqvarna 262xp not starting

    So I started a thread many moons ago about this saw. Got it with a scored piston, tore it down and put in new seals, meteor piston, spark plug, fuel line, fuel filter and new gaskets. I have not vac/pressure tested it, I know I know... Figured I would try starting it without rebuilding the carb...
  19. BonScott46

    Flaking squish band plating Jonsered 2152 cylinder

    So I have a 2005 Jonsered 2152(Husqvarna 353) that I picked up, has some miles on it and was blowing 125psi so I figured I would put a new ring on it pull the base gasket and muffler mod it to see what it could do. Pulled the cylinder and started cleaning it up when I noticed the squish band...
  20. BonScott46

    Which carb for a jonsered 2065 that is getting a big bore kit?

    Hey guys, picked up a 1998 Jonsered 2065 for around 200 bucks. It has been sitting with fuel in it for god knows how long, but other than that it is near mint. I think it has only been started a handful of times by the look of it. I was going to change the fuel filter, do a carb kit on it and...
Back
Top