Search results

Looking to buy a good used or a new crank for my 193T. Part: 11370300402 Flywheel thread end broke off my old one. With thanks R. Stihlskin.

The limiter is the same as the pic huskhl put up, good news i jammed another screw in, carefully as possible, and the limiter housing came out. Screwed out the adjustment screw and it looks in good order , no marks, no ridges but i will have a good look with a magnifying glass as my...

Well, i think Ive made it all worse, I tapped a screw in, got some pliers and gave it a good tug, nothing came out except the screw. This is appalling.

gday All, Stihl part no: 5910 890 4502 reverse ( left hand) thread screw in puller for carb limiter cap removal. I haven't tried to remove the limiter cap yet, as theres yet another proprietary tool which i havent got. Whats a good removal method to use for this caper? Carb needs a pull...

Mark, Ill have to pull them down and have a look comparison. The 194 looks more like the 193 from a cursory look. Ill report my findings as soon as i can get through work and xmas .

Thanks Mark, Ill pull down the donor 192T and replace the crankshaft to the 193T. My IPLs state those small differences in numbers. I may have got the strato mixed up as Im also assembling a 201T which is the strato system I think. Sorry for the vague, these are project saws of mine that...

Situation: 193T rebuild, doing up the flywheel nut gently and the crank broke off. Disappointing. I have an old 192T partially in pieces for parts. QUESTION: Is the 192T crankshaft a fit for the 193T? part number difference is the last 2 numbers (192T - 0400) and the (193T - 0402) I...

Gday, Seeking Service and IPL Manuals for Stihl MS181. Look forward to advice. Stihlskin

I did get under a sheet and threw it over the machine and myself looking for an arc. I know what you mean the spark is short and sharp and hard to see in the light.

Thanks for reply, I resolved the issue by setting the plug gap to spec 20 thou of inch or 0.2mm. Not mentioned anywhere in the info I had, Stihl say to use part number such and such to set spark plug gap, but its a secret. Out of the box the plugs are set to 25 thou , thereabouts, Ive never...

No Spark, Done the Stihl service flowchart diagnostics....No Spark. Blower 2 years old. It did a typical ignition failure, engine intermittent engine cut-outs for 5 or 10 secs, and died. Have trialled a donor replacement coil / module and no Spark. The old coil is happily working in the...

Gday All, Slightly off the saw chain , has anyone an IPL for a BR800 backpack Blower .

Natures Gentleman thank you.

Gday Lads, Looking for a Service manual for the KM131R , much appreciated, Stihlskin

Ended up being 66DL is the perfect size for a Stihl Rollermatic 20" bar , .404 chain, 7 tooth floating sprocket.

No thanks Chris, Im only rebuilding this one out of nostalgia it was my Fathers saw. If it works well I"ll use for camping but if its a failure it goes in the shed to collect dust or over to your place for parts.

Chris that's a tidy 066, good work! great saws. MS 066 - I've done a cylinder kit and rubbers on one, and did a full overhaul on another. Nice to work on too. The 064 was a coil replace + the usual, it had the 2 keyway flywheel so i was able to source a coil P/N? from Choina...

Thanks Patrick62 , 65 DL .404 chain starting point. 72 DL on the 3/8 chain. I expect it will cut like a beast with the .404 chain. I run .404 on my 08S , seems to cut alright. That's what it came with.