Search results

I’m working on a few 540xps One of them I didn’t do a press and vac test on, The saw runs and cuts but will have a idle change if put on its side Thinking crank seal, I have some farmertec ms 200 crank seals, the metal type with rubber They look the same soze As well as I tried some ms200...

I got a few parts saws from a tree company Seems like all of them had the mufflers fall off and melt up the tank bottom as well as mess up the exhaust port The mufflers are cracked as well I tried brazing them and as well the holes are flared outwards Looking for some replacements

Picked up 4 parts 201t saws 3 turned out to be m tronic and one just the 201t Looking for a Ipl and service manual for the m tronic All the mufflers seem to have come loose on these arborist saws, and possibly stripped the bolt holes in the cylinders

Looking for a bar tip, will the 12 tooth Oregon fit?

I recently took apart Both saws, and was puzzled when I saw the one crank had offset lobes and almost relived when I saw the other one was the same. Is this normal?

I have a Husqvarna 575 XP with a broken clutch .I tried to order a aftermarket 372 clutch to see if the clutch shoes would fit which I heard they would but it doesn’t fit I’m thinking if I got OEM Husqvarna shoes they would fit Also could I have a machinist make the 372 clutch the thread size...

Hello, so I bought a 575 xp for 110 with a scored cylinder Not knowing how or why it burned up I tore it down The bearings in the lower end felt knotchy So I split the cases The bearings has what looked like carbon or maybe burned sawdust They cleaned up well in a ultrasonic cleaner Anyways I...

I just got a 017 in new condition from my local dealer for free, it had a scrap tag on it, didn't bother asking what was wrong because I like a challenge, took it all apart, the piston looked excellent, didn't take the cylinder apart because upon noticing the pan was the pan for the single lobe...

I recently bought a used ms200 rear handle saw, whenever I buy a saw I strip it down and check everything after a good cleaning. i noticed a crack in the case right where the bolt goes just to the left of the chain tensioner opposite of the bar stud. at this point I'm wondering if i should buy...

I rebuilt my ms170 with a farmer tech 38mm cylinder and piston, new crank and bearings, seals eat, i used the poem bottom clamshell , ran the saw for a few weeks, it ran great, then It was running erratic and would bog, i noticed some scoring on the flywheel, i then could feel up and down play...

hello, I have a ms362 that the previous owner installed a timesert crooked in the cylinder, I had a machinist try to level the aluminum mating surface with a end mill to the angle of the insert it seemed to be ok with a brand new plug, but not for long, would this leak cause a failure? i have a...

I recently bought a used ms 261 and after tearing it down for cleaning and putting it together i fuelled it up and noticed gas leaking out of the tank vent, bought a new vent from the dealer and asked about installation and if i had to remove the handle assembly, he said no it just pushes in...

hello I bought a ms362 used and tore it all down for cleaning and inspection it seemed to rev without burbling, and did not really respond to richening the high side carb adjustment it almost sounded like the ignition was limited. i also noticed a bit of white smoke coming from around the clutch...

Hello I bought a MS362 yesterday for $360 yesterday in good condition, did i get a deal? the piston looks new upon looking through the exhaust the bar is a es bar with replaceable tip, it had quite a bit of burrs on it, i have removed the majority before I sliced open my thumb pretty bad and...

hello, going to look a ms362 for sale , they are asking $400 and tell me its in great shape and runs well , it looks to be in good shape, haven't seen it up close though, I was wondering what parts from a 361 would fit? what are common things to look for, I'm going to ask to remove the muffler...

I am in the process of rebuilding a 029 super, it had a leaky fuel line, I'm assuming thats why the piston was scored when i got it i have ordered a farmertec 390 cylinder and piston, bearings, seals. should be here soon when i took the crank out, one of the crank bearings came off fairly...