Search results

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. tbohn

    Huztl / Farmertec MS 460 Clone

    They going for $237 shipped now. I'm thinking about getting another and installing a big bore 54mm p&c on it. My Huztl 660 big bore is noticeably stronger than stock. I'd also like to compare a 54mm 460 against a 54mm 660.
  2. tbohn

    Huztl / Farmertec MS 460 Clone

    Couple of tanks through it. My Huztl 440 has a lot more vibration than the 460 kit. The 460 is more like my Huztl 660.
  3. tbohn

    Huztl / Farmertec MS 460 Clone

    Had chance to cut some with the Huztl 460. After about a half tank of running it rich, I adjusted the carb to 4 stroke out of the cut and clean up in the cut. The saw cuts great. Sent from my SM-G955U using Tapatalk
  4. tbohn

    Huztl / Farmertec MS 460 Clone

    I just finished my Huztl MS 460 kit. I have started it but have not cut with it. I installed the P&C that came in the kit. I've built both the Huztl 440 and 660. The 460 kit is a lot like the 660 kit but smaller. The Good- The kit had all the parts and they went together well. The quality...
  5. tbohn

    Huztl FarmerTec MS380, MS381, 038 Build Kit Start to Finish

    Or maybe the ID is too large...I can't remember. Sent from my SM-G955U using Tapatalk
  6. tbohn

    Huztl FarmerTec MS380, MS381, 038 Build Kit Start to Finish

    I think the had a 10mm and 12mm. The 12mm fits on the ms380 wrist pin but it's OD is too small. Sent from my SM-G955U using Tapatalk
  7. tbohn

    Huztl FarmerTec MS380, MS381, 038 Build Kit Start to Finish

    I have not built the ms360 or ms361 kits. I've built at least one of everything else. I think the ms660 kit is the best deal and the quality is good. I think the ms380 kits are the best quality and and most heavy duty. Sent from my SM-G955U using Tapatalk
  8. tbohn

    Huztl FarmerTec MS380, MS381, 038 Build Kit Start to Finish

    When you have a ms440 wrist pin bearing in a ms380 you can tell. I installed the correct bearing and all is good. Sent from my SM-G955U using Tapatalk
  9. tbohn

    Huztl FarmerTec What Saw Build Kit Would You Like to See Them Make?

    Farmertec hasn't had any specials on the Huztl and Arbortec sites lately. What gives? Their daily/weekly specials keep me coming back to their websites.
  10. tbohn

    Huztl FarmerTec 070 Build Thread with upgrade info and completed saw

    I have built two of the 070 but I have broken rings in the past. I struggled in the past getting the lower ring installed when installing from the top of the piston. Sent from my SM-N900V using Tapatalk
  11. tbohn

    Huztl FarmerTec 070 Build Thread with upgrade info and completed saw

    I found it easiest to install the lower ring by sliding it on from the bottom of the piston. Sent from my SM-N900V using Tapatalk
  12. tbohn

    Huztl FarmerTec 070 Build Thread with upgrade info and completed saw

    I built a second 070 kit and had fuel difficulties when trying to start it. It thought I had a leak somewhere but after checking it several times I eliminated that as a consideration. I finally decided to take off the cylinder and look at the impulse line. The impulse hole is located on the...
  13. tbohn

    Huztl FarmerTec What Saw Build Kit Would You Like to See Them Make?

    Are Huztl 090 cylinders available yet?
  14. tbohn

    Huztl FarmerTec 070 Build Thread with upgrade info and completed saw

    Rotating the ignition module sure looks like it would give you a few degrees of timing adjustment. Rotating it clockwise would have to advance the timing. I set mine in the middle of the adjustment and it runs good. Maybe when I get a chance in wood I will see what adjusting it will do. The...
  15. tbohn

    Huztl FarmerTec 070 Build Thread with upgrade info and completed saw

    Where are you getting the 090 cylinder kit from? What is the 15mm snap ring for? Have you found out more about the timing adjustment on the stator plate? I put mine in the middle of the adjustment and it runs good. This has to have an impact on the ignition timing - clockwise adjustment...
  16. tbohn

    Huztl MS660

    I think I will get resolution to the issue. They said they will send replacement housings (the orange part of the rear handle) to replace the defective ones. I put together a ms180 kit yesterday and had several broken parts and a few missing parts. It was interesting that some of the broken...
  17. tbohn

    Huztl MS660

    I ordered some rear handle assemblies from Huztl ebay. They are not the same quality as what I have been receiving from Huztl. They are a flat finish unlike oem and the texture of the plastic appears low quality. They probably received a bad batch from a supplier. The issue is that they have...
  18. tbohn

    Huztl FarmerTec 070 Build Thread with upgrade info and completed saw

    I had the chain catcher installed incorrectly. It's all good now. Sent from my SM-N900V using Tapatalk
  19. tbohn

    Huztl FarmerTec 070 Build Thread with upgrade info and completed saw

    Here it is with the bar mounted. The chain catcher is too long and is preventing the cover from completely contacting the bar. I will either shorten the metal chain catcher or just pull the cover down with the bar nuts. Sent from my SM-N900V using Tapatalk
  20. tbohn

    Huztl FarmerTec 070 Build Thread with upgrade info and completed saw

    I didn't have it so I deleted it. The stator is offset from the seal. My guess it was there to keep the points cleaner when they have points. Sent from my SM-N900V using Tapatalk
Back
Top