Search results

I’m continuing my porting adventure on the CP 55. Finished one and I want to try version #2. Looking for really nice shape cosmetically..... ie bright clean plastics. Not sun faded- even with a bad top end as I have no use for an open port cylinder. I have several CP cylinders. Saw will be...

anybody run one of these toads? I’ve had this in my overflow saw trailer- loads of compression but needs carb gone through etc. do they run with the torque to justify the boat anchor like weight?

Acquired a super pro 70 and a 7-10. The guy had pulled the recoil off the 7-10 to put on the 70. So.... I’d like to find the SP recoil cover assembly and get this one back on the 7-10. I also need the two bolts to mount the coil on the 7-10. Or if anybody knows these size/thread pitch? thank...

Looking for a good OEM fuel tank for an 064. Please PM me with price shipped to 83616 thank you. Trent

please PM me if you have one to sell. Shipped to 83616. Beat to H**L and drastically over priced moves right to the top :)

If anybody has one to sell :) Trent

I’ve got crank cases (with cranks) for 181/281/288. They will need new bearings and seals, and I could rebuild for you before shipping if needed. $75 for crank and case. I have a few fuel tanks also. But they are missing caps, anti vibes, throttle arms, presence levers, etc. $25 for tanks...

Rebuilding a Stihl 044 and have a case half with some mag issues. looking for a flywheel side case half. Would happily buy the whole case if somebody doesn’t want to split. Please PM me with price, shipped to 83616 trent

Have a saw that needs a few parts....... if anybody has the following please float me a PM :) I would also buy a whole parts saw if available. Doesn’t need to be pretty. 154se air filter Top cover Muffler and muffler bolts Clutch cover with chain brake....... I do have a cover but no brake...

I’ve already researched- not much info on these saws I need to replace the Oiler- and likely change crank seals while I’m in there . I’ve already removed the pump housing screws..... but it seems held down by what I believe to be the Oiler gear. Is that thing a press fit? any advice to...

I’m not well versed in the older saws. can anybody enlighten me as to the model, and a bit of info on the machine pictured? thank you Trent

Splitting the case on a Stihl 044 10mm...... there’s one case bolt left to pull and I can’t tell if it’s a snapped off head or what..... if it isn’t it’s an entirely different size than the rest of the case bolts. It’s the one on the front of the case..... can anybody enlighten me on this bolt...

Looking for an OEM 385xp cylinder. Thank you! shipped to 83616 trent

A good friend of mine is a chainsaw nut and I recently got an old 44 practica that was his grandfathers. I’m working to rebuild the saw as close as possible to it’s original condition so that I can gift him the saw. I got it in pieces. I’ve found a lot of new OEM parts- but I’ve been unable to...

Thinning the boxes of cylinders..... I’m pretty certain I’ve got each model correct but please let me know if you see anything that’s incorrect. note- the 394 cylinder has a piece missing where the cylinder skirt drops into the case. Won’t effect performance one bit..... but it’s there. It was...

I’m not a Stihl guy and I know these saws came with more than one crank/piston combo this one is a 10mm wrist pin...... so I ordered a meteor piston for the saw...... put it on and something is off. There is some serious machine difference here....... this piston can walk a good 1/4”+. am I...

OEM fuel tank handle wanted TIA Trent

I’m cleaning out my McCulloch stuff and for the life of me I cannot remember what this cylinder and parts long belonged to. I do remember that the bracket was a motor mount adapter for a cart..... and the other is a setup so that 2 carburetors can be run (also for a cart). Can somebody tell...

Not sure the best way to do this.... going through the saw storage and eliminating some yellow. Bottom line pick a part via PM and I’ll give you a price...... or $125 plus shipping (83616) for all pictured. Looks like a mostly complete saw..... keep in mind I don’t know McCulloch very well...