Search results

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. J

    British English Chainsaw Terms VS American English?

    I've heard: " You invented this language and can't even speak it." Pertaining to England and their speaking /slang.
  2. J

    Want to Buy Walbro WT439 Carb...

    I just did a poor man fix I initially wanted to just make the carb adjustable and remove limiters but it ended up being way harder lol. Clamshell saws!!! now I see the problem! Figured I'd just reroute the fuel line grind the nipple fitting..and install a new line easy right? Pulled the line it...
  3. J

    Want to Buy Walbro WT439 Carb...

    At least ya responded to my thread haha hard to get an answer here fast when ya need one.
  4. J

    Want to Buy Walbro WT439 Carb...

    Thanks for the reply, did ya mean 3516 or the 1635 I'm looking for? Carb looks similar to the one I have but fuel and vent line are in different spots. I'd like to keep the same carb if at all possible, but I appreciate you showing me this one I might need it if no one comes through.
  5. J

    Hi.

    This uncle Moustache guy is on the right track but don't give him the bank number just pay the monthly dues lol. Welcome!
  6. J

    Want to Buy Walbro WT439 Carb...

    Hey Guys Need the black 90 degree plastic elbow for this carb (Walbro WT 439) it's either a fuel or carb vent line I could make it work but the line is short and the brass fitting left has a short barb. It's for my super reliable McCulloch MS1635 beater this saw starts no matter how long you...
  7. J

    Tuning a saw to factory RPM while increasing oil % in mix

    Bump. Threads seem to drop quick on this site I must say. What's up bros
  8. J

    Tuning a saw to factory RPM while increasing oil % in mix

    Finally got my Fast-Tach in the mail seems to work okay have to move it around to find the super sweet spot, I'm not experienced in tuning at all I play with my Mac 10-10 just for practice but what a different animal these new saws are. I tried tuning the stilh 391 based on rpm Low/High and Idle...
  9. J

    Tuning a saw to factory RPM while increasing oil % in mix

    I have a strato Ms 391 and a Husky 3120xp I recently removed the limiter caps from the 391 and I'm having a hard time tuning it by ear for the -High- I was almost 2 turns out for 4 stroking by my ear,I have good hearing but not that sensitive to sound change. I initially was going to tune by...
  10. J

    Adjusting H screw only for milling/ General tuning questions

    Thanks for the reply. I ordered a tach and it should be here tomorrow so I'll tune by ear and rpm shooting for rich on the H side. I'll let you know how it goes.
  11. J

    Adjusting H screw only for milling/ General tuning questions

    I just aligned the notch in the limiter with carb and pulled once I finally got a bite with the pulling screw, I did cut the tab off as well!
  12. J

    Adjusting H screw only for milling/ General tuning questions

    Finally got the limiters out of my MS391! What a ***** the H-screw was, L was easy, I did it all with the carb in the saw with rear air filter mount loosened but still intact which gave me more access to the L but didn't give me any working room on the high. I did cut the black screw driver...
  13. J

    Adjusting H screw only for milling/ General tuning questions

    Man I ripped a tag off a mattress once or twice maybe 3 times lol I'd like to rip this **** off of the saw too, do you know of any videos showing the general procedure? The saw being as new as it is I'm having a hard time tearing into it even though the factory settings are probably more...
  14. J

    Adjusting H screw only for milling/ General tuning questions

    I have a few old saw but I wanted newer saws ready to run with safety features, might have went too new nothing but safety and limitations haha
  15. J

    Adjusting H screw only for milling/ General tuning questions

    Yeah my 3120xp is limited by a 9600rpm? coil and no H speed adjustment, just realized I've become a collector of EPA saws WTF! Haha I think you can purchase an adjustable carb for the 3120 or enlarge the orifice on the fixed H jet. I guess my only option to richen up the MS391 H screw is to...
  16. J

    Adjusting H screw only for milling/ General tuning questions

    How do you delete this?
  17. J

    Adjusting H screw only for milling/ General tuning questions

    Just found out my MS391 H screw is basically non adjustable for richer settings, while waiting for a response to this thread I turned the screw in to seat and back out to original (factory )setting...3/4 in 3/4 out nothing more then this! 3/4 out is where it was and the max!
  18. J

    Adjusting H screw only for milling/ General tuning questions

    I get the basics of tuning a saw and I'm still learning, I have a new Ms391 just broken in I've been using it for milling small logs and plan to use my 3120xp for large ones. My question is can I slightly increase the high screw for a little extra 4-stroking at WOT W/O changing idle and L screw...
  19. J

    Saw setup for milling: Oil%/H screw setting/Rev limiters/Non-Adj. Carbs...ETC.

    Thanks for the excellent reply BobL looks like I have some reading to do.
  20. J

    ID my old Mac!

    I'll try and get some pictures up might not work since I'm on a mobile phone.
Back
Top