Search results

Have a well used 385xp I would like to sell. Has some broke fins, little case damage on the right back corner under where the air filter cover attaches. Saw seems to run ok and appears to work as it should. Will sit and idle fine, revs up and doesn’t seem to have an obvious problems. I have not...

Have a very nice jonsered 2258. Had the unit several years and only ran 6 or so tanks though it. Nice clean unit. Runs, idles starts as it should. All oem minus a meteor piston. Don’t have a compression tester for the smaller spark plug threads. Can pull the muffler and try to get a pic if...

Had this saw a while. Runs great just don’t have a need for it here in Texas really. Trying to downsize. Ask any questions you like. It’s all oem minus a meteor piston. $700 PHO shipped and insured via FedEx. Sent from my iPhone using Tapatalk

Have a nice jonsered 2165 that sits more than gets used. Bought this a few years back and it had been straight gassed. Cleaned up transfer off the cylinder and replaced piston. Only aftermarket part is a meteor piston. Runs, oils, and cuts as it should. Nice unit. Thinking $450 shipped PHO...

Selling a new 2166. Bought this from an older gentleman little over a year ago and he didn’t think he had ever started it. I haven’t used it at all. Has a few scuffs on the wrap from being moved around and one under the muffler. Will come with a new 24” 058 bar and chain. $600 PayPal plus...

Have an 064 that I purchased needing a few parts. I purchased the aftermarket hd filter setup that was listed for an 064 but clearly doesn’t fit. Any help on locating correct parts to fit would be appreciated. I wouldn’t mind the original filter setup if I could find the parts for that...

I’ve decided I’m going to sell this 394xp. It needs a little work still but is complete. All oem except piston and clutch. Mahle cylinder that was nice. It does run, but needs a carb kit at a bare min. It is missing the screws and nut/inserts that mount the bottom of the handle to the tank...

Put this back together after it was straight gassed early in its life. Sat for a few years. I put a used but very nice 562xp cylinder with wider transfers on it with a new piston. It is very clean and works as it should. I have installed a bucking spike that is not pictured. I am...

So I bought a nice 394xp and has a broken piston and am assuming it needs a jug. I don’t have it yet in my possession. Anyone have a good oem cylinder? Sent from my iPhone using Tapatalk

Looking for a useable 390xp cylinder one before I buy new. Will consider a 385xp also. Sent from my iPhone using Tapatalk

Decided to put my 359 up for sale and see if there is any interest. Have too many 60cc saws. I decked, mild port(widen exhaust, opened transfers) popup piston. Only aftermarket parts that I know of are muffler(I brazed a 1” pipe) clutch cover, and piston. Pretty clean saw. It has decent...

Have a saw I picked up not long ago needing an oil tank and wrap. I swapped with oem parts. I picked this up for my brother in law but he has since picked up something else. Haven’t done a compression test but piston looks great. Saw runs and oils as it should. This is a PHO only and no bar...

Acquired too many saws so going to try and downsize a bit. This is the first to go. Good old saw. Lightly ported, ported aftermarket muffler, and had an aftermarket piston and new crank seals. Has an aftermarket 272xp top and the front left screw hole was drilled/tapped and is stripped...

Just kinda looking for a bigger Husky to build and seeing what is out there. Biggest I have is a 372xp. This is more less just a hobby for me and I use it for some light firewood, lol May consider some Stihl saws.

Had this a while and picked up a 372xp. Looking to move this as I don't really need it now. Closed port 48mm mahle oem cylinder, I put an aftermarket piston in it. Oils well. Looks rough. Runs pretty good, lots of power. Selling as a pho due to shipping being less. PayPal preferred. Will...

Had this a while and played with it some but it's way bigger than I need. My 162 and 372xp are plenty for me. Complete good running 181se. Has 150 psi and original mahle jug. Aftermarket muffler and piston. Tons of power. It just sits so I thought I would see if anyone was interested in...

Picked this up not long ago and then found a 372xp that I had to have. This has some miles on it, but runs good. Looses its prime after it sits a week or so, but runs and idles good. Looks to have an aftermarket cylinder and I'm assuming piston not long ago. $250 shipped to lower 48 via...