Search results

I'm looking to buy either an entire saw,engine need not be good.I need the carry handle,part # 6074991,which is supposed to fit all 3 models in the title.Mounting screws would be a plus. I also need the OPL (operator's presence lever),part # 6074989.

According to the IPL,these saws are all grouped together & the clutch/chain sprocket covers are all interchangeable.

I'm looking to buy either a parts 2-10 or the muffler assembly,or the muffler cap & baffle.

I'm looking for a PM 10-10 complete chain brake/clutch cover in working order to fit a model# 600014U,suffix of 12.It's supposed to be the long chain brake.

Wanted to buy - new rings for a Remington PL5 or SL11.

I'm looking for a good engine (piston & cylinder) for an SL11.Will buy the whole saw for parts.Reasonable prices please.

Looking for a Remington PL5 or SL11 with a good cylinder & piston.My saw is in great shape,but I just found the piston & rings has a gash all the way down the length of the piston.I don't know if the cylinder is shot or not at this point.I hate pulling things apart & waiting on a part...

I'm looking for either a complete manual oil pump plunger,or the button that fits the oil pump plunger.Also,I need the clutch cover & fuel cap.

Looking to buy a 10-10S in halfway decent shape.I don't want a saw that needs a rebuild or seals.Carb work,fuel line needed,recoil or chain brake work are all OK if needed,or no spark issues OK too.

I'm looking for a Remington PL4 or PL5 with a good engine.I don't mind simple repairs like new fuel line,recoil work,carb rebuild,or anything of that nature.I don't want a saw that needs crank seals or a complete rebuild.Bar & chain are not necessary.

I need a set (2) of clutch springs (newer style) part # 66847 for my SL-9.

Hello,I'm looking to buy a set of bar plates in good condition.I can also use a good used set of guide bar studs w/nuts.I'll also pay the shipping.

I'm looking for an electronic ignition module for my Poulan S25DA.This is made by Phelon.Part #39088

I'd like to buy a bar to fit a Remington Super 754.I understand that it uses a Homelite mount pattern D096 or D196.I'd like the bar to be 30 in.if possible,hard nose is fine,but sprocket tip,or roller nose is preferred.If it's the Remington bar it'll be .058 gauge,a Homelite or Oregon or...

Wanted to buy - a complete starter/recoil assembly for a Remington SL9.Even if you only have the outer shell,or the internal parts that would be a good start.

I'm looking to buy either a C9 or C91 that can be put into running condition without a ton of work.I don't mind putting on a new fuel line,rebuilding the carb,or repairing the recoil assembly,but I'd rather not do a complete rebuild on the engine,I already have a project saw of that...

Looking for a Homelite C9 or C91 to tinker with.Total rebuild not out of the picture,but one with good P&C is better.Does not have to be complete or have bar & chain.I DON"T need a shelf queen.Looking in the $75 range or less,higher than this is not out of the question depending on condition.

Wanted to buy - Walbro SDC2 carbs for early 10-10's & 2-10's

McCulloch 1-50 coil.I've seen one on Ebay for sale,but it has a short plug wire on it which leads me to believe that it's for a 380,not a 1-50.Maybe they took the same coil?

I've got this furnace,not a wood stove,it takes odd ball sized fire bricks that are 9x4.5x2.The last time I replaced them was around 1991 & I had a heck of a time getting them.We had to take a one hr.drive to get them.I see on Feebay that they have insulating fire bricks,but are they the same as...