Search results

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. A

    The Beg for Manuals Thread

    I need a ms151tc workshop manual
  2. A

    The beg for manuals thread

    I need a workshop manual for a ms151tc
  3. A

    Bc1500 tach problem

    It was the tach itself it was fried
  4. A

    Bc1500 tach problem

    Problem is fixed the tach itself was fried. Had to buy a new tach through vermeer due to updated part numbers but you can buy it through other places that sell datcon tachs. Cost from vermeer was 340 dollars
  5. A

    Bc1500 tach problem

    I put a test light in the plug ends and im only getting power from one wire. Should the tach signal temp voltage and oil pressure also show power coming out of the plug or are they grounds. I also found the fuses and none were bad. I need a wiring diagram to trace the wires. Im not sure how the...
  6. A

    Bc1500 tach problem

    I will check that out and make sure there is signal coming. I dont think that all the sensors would go bad at the same time. Im also gonna trace wires back to sources to be sure they are all good. Im thinkin since its one of those smart tachs the computer board in it went bad from sitting
  7. A

    Bc1500 tach problem

    The tach does light up and does do the intial sweep of the rpms but thats it. Im also having a problem with the trailer brakes not working correctly but im not sure where they ground at. Im thinking maybe the tach is bad this machine sat for a few yrs in a garage. I went over all the wires and i...
  8. A

    Bc1500 tach problem

    And yes all lights are green on the autofeed controller
  9. A

    Bc1500 tach problem

    Yes the autofeed works correctly everything works except the tach and the tach on it reads the water temp oil pressure voltage and hrs i found where the one wite that was unhooked went to it was to a fuel filter i plugged it in and same no tach but runs just fiine
  10. A

    Bc1500 tach problem

    I just bought a 2009 bc1500 and the tach isnt working. When you turn the key on it does the intial sweep of the tach but says 0rpm when running and when you hit the info button its not reading any of the sensors like temp oil pressure or hours. I did find a wire unplugged but cant find where it...
  11. A

    Mtronic idle adjustment

    Well when you try to act like your better than everyone it bothers some people. That screw opens the throttle blade just as it would on any carb. You must have that open enough to start or idle. Do you even know how a carb works because it sounds like you dont. And what if i had it more than 2...
  12. A

    Mtronic idle adjustment

    I turned it one full turn and it fixed every problem i was having down to the starting issue where i had to hold the throttle open a tiny bit when starting i had to remove the trigger unit its called not throttle sensor. You have to remove that to get to that tiny screw. Im not sure if it was a...
  13. A

    Mtronic idle adjustment

    And yes it fires rught up now first pull two pulls cold so hmmm think about that
  14. A

    Mtronic idle adjustment

    You must not know to much about it cuz its fixed now and runs fine and yes there is a throttle sensor u want the part number look it up 1145 430 1001 trigger unit is its name but it triggers something when you turn on the choke and did you ever happen to think that from factory that screw wasnt...
  15. A

    Ms201t idle adjustment

    Hi there im wondering why nobody has noted the idle adjust screw on the ms201t with mtronics idk how to post it anywhere and your top of the list but yes if you have problems with your mtronic not wanting to idle or start and the factory default reset does not help take the carb off and remove...
  16. A

    Mtronic idle adjustment

    Hi there im wondering why nobody has noted the idle adjust screw on the ms201t with mtronics if you have problems with your mtronic not wanting to idle or start and the factory default reset does not help take the carb off and remove the throttle sensor and there is a small block where the...
  17. A

    The Beg for Manuals Thread

    I need the ms201 with mtronics workshop manual and ipl
  18. A

    Need help with old altec chipper

    I have an old chuck and duck 16" chipper. I was told its an altec maybe from 60s-70s. I need a few things like how to make my blade adjustment screws stay in place and need bearings for it how hard are they to and the cutter bar how to flip and set it up. Im not sure of the model or year because...
  19. A

    The Beg for Manuals Thread

    Need a workshop manual for ms211
  20. A

    The Beg for Manuals Thread

    Ms311 workshop manual
Back
Top