Search results

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. U

    Want to Sell Husqvarna 576XPW

    Where in CT?
  2. U

    Top Handle Recommendations

    Hahahaha no, I think they are worse than the stumps. I have to change that, just moved a few weeks ago. Sick and tired of hurricanes.
  3. U

    Top Handle Recommendations

    And that is something that most people don’t have the patience for. They think right out of the box (or right from the porter) its at full power. This is one of the reasons that I try to put at least 2 full tanks through any saw I build. Get some break in time and make some tune adjustments...
  4. U

    Top Handle Recommendations

    That airbox mod requires some pictures to explain correctly, but, yes it does help. The most important thing with these little saws is break in. They take around 10 tanks to really break in, regardless of mods. If you run a mm/tuned saw side by side with a stock one (both broken in) there is a...
  5. U

    Top Handle Recommendations

    I like to remove the deflector, mod the gasket to open it up a little, cut back the inside of the deflector divertor. Have to be careful punching the divertor down, it will spread the deflector out. Also have to be careful drilling the hole, too high and it will melt the plastic, too low and it...
  6. U

    Top Handle Recommendations

    The muff mod and tune REALLY wake up these little saws. A good little port job is even better.
  7. U

    Top Handle Recommendations

    Do yourself a favor: muff mod and tune it. Grab a fine thread sheetrock screw and screw it into the red plastic h adjuster on the carb. Don’t worry about changing the setting. Just thread it right in and keep turning, the red plastic lock will push up against the small aluminum frame that...
  8. U

    Top Handle Recommendations

    I think, and its my opinion only, the 200 is more robust than the 201. The 201 doesn’t seem to be as ruggedly built. I am not a huge fan of the 201, although with good porting they will hang with a 200. As with everything there is a lot of trade-off when saving weight and making things compact...
  9. U

    Top Handle Recommendations

    I have both 2511 and 355, have run the 192/3 (can’t stand them) 200T (good saw) and the 201. I have also ported all of them. Bang for the buck: Echo. For longevity the 200T is king. But, you can get 2 of the Echos for the cost of a 201T. Personally i prefer the ergonomics of the 2511 and 355...
  10. U

    Boots boots boots

    Torrington area here.
  11. U

    Husky 455 to 460 upgrade and porting

    I know they are under-powered slugs; I was busting @mettee ’s stones is all.
  12. U

    Husky 455 to 460 upgrade and porting

    Is this saw done yet?
  13. U

    Want to Trade Two stihl084s for stihl or husky saws. What do you have?

    I have a 576 about to get a new OEM p/c and full wrap. Going to port it.
  14. U

    Sold Stihl ms271

    I’ll take it.
  15. U

    Want to Sell 024

    PM sent on 036
  16. U

    Want to Trade Glock 21 for saw

    Yes. Glock 21sf RTF2. Fish gill slide serrations. I had one and not knowing what it was sold it like a dumbass.
  17. U

    Want to Trade Glock 21 for saw

    Any specific saw you are looking for? I have a couple here. Is that Glock a 21SF? Any possibility it is a 21SF RTF?
  18. U

    Want to Sell Want to trade

    025 cyl, crank and piston?
  19. U

    Want to Buy Husqvarna 242

    Do you have the new part numbers for these seals?
Back
Top