Search results

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. dmitriy

    FarmerTec Huztl MS660 Updated Build Kit - Build Thread

    Quick question: Anyone run into a problem where the kill switch doesn't shut the saw off? (metered it and it seems the the 2 leads coming off the coil always have continuity - new coil?)
  2. dmitriy

    FarmerTec Huztl MS660 Updated Build Kit - Build Thread

    The wire was included but I didn't use it since the chainsaw spark plug / wire are close enough to the tach for the magnetic field to work. It has a resettable max RPM history as well as ability to switch for different ignition types. Refresh rate of about 1 second and judging by this video...
  3. dmitriy

    FarmerTec Huztl MS660 Updated Build Kit - Build Thread

    Got the tach, no need for a coil wrap either!! (Seems to work same as the stihl one) A little 3M dual lock and it's on there. Gotta pick up the wrist pin / bearing and swap those & fuel cap plus put down some heat shielding
  4. dmitriy

    FarmerTec Huztl MS660 Updated Build Kit - Build Thread

    I forget if there was a reason you can't just change the main jet instead of the whole carb? (I bought mine from mittysupply)
  5. dmitriy

    FarmerTec Huztl MS660 Updated Build Kit - Build Thread

    Thank you, I try with pictures to give back what I can to the forum since you guys have been VERY helpful in this journey! Do you think this Tach look VERY similar to the Stihl EDT 9? https://www.rockymountainatvmc.com/p/984/82332/Tusk-Tach-Hour-Meter I may try ordering that one as I had good...
  6. dmitriy

    FarmerTec Huztl MS660 Updated Build Kit - Build Thread

    Not sure on the cylinder name will have to look around on it (it was in a Farmertec box but that doesn't mean anything). I did my squish opposite sides one through spark plug one through decompression valve (above intake / exhaust ports) though to be thorough I guess I could gone with the 4...
  7. dmitriy

    FarmerTec Huztl MS660 Updated Build Kit - Build Thread

    Mine was 0.020 WITH the metal base gasket (one with indents and wings) I think I measured right- inserted solder through decompression and spark plug holes at the same time and cranked it over then measured the solder Squish area...???
  8. dmitriy

    FarmerTec Huztl MS660 Updated Build Kit - Build Thread

    Yep first one! Not sure what's going on with the last 5 pics they load OK for me... Hmmmmm Squish was 0.020-0.022 Used Hondabond on the case gasket just to be sure Beveled the cylinder ports a bit to make sure I don't hang a ring. They came rough from the casting it seems. Does anyone have a...
  9. dmitriy

    FarmerTec Huztl MS660 Updated Build Kit - Build Thread

    So got my kit all together and it runs!!! (Got more then a few OEM parts on order). 76 carb already on there. Of course they missed a few screws and an e-clip the brake pin was included but not installed
  10. dmitriy

    FarmerTec Huztl MS660 Updated Build Kit - Build Thread

    Just measured the piston again (somehow the previous measurements are incorrect) Piston: Top (ring) 53.81-83mm Bottom (skirt area) 53.97mm So here are the measurements I got with piston in cylinder all the way in (so measurement take at about 1/2 up the bore), no rings, piston pushed to 1...
  11. dmitriy

    FarmerTec Huztl MS660 Updated Build Kit - Build Thread

    Just stopped by the local dealer and got some prices, are these in line with what you guys are paying? $7.00 #9512 003 3281 - OEM piston bearing $21.00 #1122 034 1500 - wrist pin OEM $14.80 #1122 160 5400 - Brake Band $8.40 #1122 160 5500 - Brake Tension Spring $16.69 #1128 020 9400 - Decomp...
  12. dmitriy

    FarmerTec Huztl MS660 Updated Build Kit - Build Thread

    Awesome, Thank you! :bowdown:
  13. dmitriy

    FarmerTec Huztl MS660 Updated Build Kit - Build Thread

    Ok I will double check. Does anyone have a current IPL for the 660? The one I have is from 2004 and it doesn't quite match some of the part numbers on this list to replace with OEM parts (thank you @Bedford T ): #9512 003 3281 - OEM piston bearing #1122 034 1500 - wrist pin OEM #1122 160 5400...
  14. dmitriy

    FarmerTec Huztl MS660 Updated Build Kit - Build Thread

    Got my kit in the mail, let the fun begin. Measure the piston / cylinder & ring gap: Piston 53.95mm mostly consistent Cylinder top and mid ~53.97-53.98mm bottom skirt ~54.01-54.02mm HMMM maybe thats why they suck Ring gap: .3mm & .35mm measured mid cylinder Anyone have input on this other then...
  15. dmitriy

    FarmerTec Huztl MS660 Updated Build Kit - Build Thread

    Nice! How much was that meteor kit?
  16. dmitriy

    FarmerTec Huztl MS660 Updated Build Kit - Build Thread

    I have a bore guage, do you happen to have measurements and clearance spec for oem parts? I can check how far off the AM ones I get are and if they are 'oval' or not.
  17. dmitriy

    FarmerTec Huztl MS660 Updated Build Kit - Build Thread

    Thx guys I live sea level so ordered the carb. Once the kit gets here I definitely get the oem parts necessary for longevity!
  18. dmitriy

    FarmerTec Huztl MS660 Updated Build Kit - Build Thread

    So what is the consensus (if there is one) is the parts kit Carb good enough or should I order a WJ-76? Finally ordered the 660 kit since it was on sale.
  19. dmitriy

    FarmerTec Huztl MS660 Updated Build Kit - Build Thread

    Would anyone be so kind as to drop me a PM with a shop manual / IPL for one of these? I am evaluating options on purchasing a kit and making a work plan for it. I saw recently the kit dropped in price from $186 to ~$140ish (with $80 in shipping fees) is that about the best discount those guys...
Back
Top