Search results

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. Matthew Steingass

    Sure is quiet in here....do I need to start a fight?

    Best saw ever made and no flippy caps!
  2. Matthew Steingass

    Carb screw governors at richest setting.

    I appreciate you're input. Beautiful country out here. I'll clean the carb and pull the limiters tomorrow morning and see how she does.
  3. Matthew Steingass

    Carb screw governors at richest setting.

    My 020t has has parts from two different carbs so I can have a walbro carb with a high speed adjustment. I've started from zero a few times before but I can't quite get there with these saws.
  4. Matthew Steingass

    Carb screw governors at richest setting.

    Im Thanks for the info and advise. I'll go for some diagrams first. It doesn't run erratically and only stumbles off idle here and there. I figured it was getting outside air given our elevation and how rich I have it. About half it's life was ethanol gas other half ethanol free.
  5. Matthew Steingass

    Carb screw governors at richest setting.

    Thats why I'm torn on putting much free time into them or asking them to get me parts. I don't like their saws lol. When I rebuild a saw I rip through money and there's a lot of trial and error. I've been wanting to just pull the governors and run them till they won't.
  6. Matthew Steingass

    Carb screw governors at richest setting.

    Ms 251 and a 271. My saws run well. Yes I mean the limits on the carb screws. Carbs haven't been rebuilt.
  7. Matthew Steingass

    Carb screw governors at richest setting.

    We work at 7 to 10,000 feet and I have a few tools that seem to need more fuel off idle (bogs) and I can't get to 4 stroke wide open. These are older tools with an unknown history at a not for profit. I've never been through the the life of a saw so I'm wondering what we should do. Fuel and...
  8. 20191211_151119

    20191211_151119

    Deer Valley
  9. Gasser85

    Gasser85

    Utah
  10. Matthew Steingass

    Want to Sell MS200T 020T parts $80 shipped

    Cylinder looks to have aluminum smear. I was going to clean it up and use it with the piston that came out of my running 020T. 020t head gasket. Cases match. Good lower rod bearing. 1 short case screw out of 6 on the upper oil reservoir. Newer compensating China carb from my 020T. Stihl iida...
  11. Matthew Steingass

    Sold NIB 390XP

    Nice
  12. Matthew Steingass

    Want to Buy 020t ms200t clutch cover.

    Looking for one that's not badly melted and has all the plastic below the muffler.
  13. Matthew Steingass

    Sold NIB 390XP

    Probably one of the best NIB deals on a feller/miller around. Simple to work on. Low vibes. Air injection.
  14. Matthew Steingass

    Sold Stihl 034 chainsaw great compression

    It'll complete my 3 saw plan. Probably be my only ported saw. Staying 46mm.
  15. Matthew Steingass

    Want to Sell Stihl MS360 builder

    If he has 2 then I need 2! It'll be fun to compare them side by side stock. I'll take this one too Brandon.
  16. Matthew Steingass

    Want to Sell Stihl 090 taking offers

    It didnt. But if it's no longer for sale at least it wouldn't waste anyone else's time.
  17. Matthew Steingass

    Want to Sell Stihl 090 taking offers

    Could you change the thread to sold as well.
Back
Top