Search results

I acquired a Stihl MS-250 recently that was missing the air filter cover. I got it to run with some fuel mix poured in the carb throat. When I started looking into it closely, the carburetor is mounted so closely to the cylinder that the front adjustment screw is completely covered by the...

For sale is a Husqvarna 359 PHO for parts or repair. This saw has low compression (~90 psi). I did not take photos of the piston, but I did remove the muffler and the exhaust side of the piston has significant scoring on it. The cylinder would also be expected to have aluminum transfer, but I...

SOLD Combo #1: Used OEM Stihl Chainsaw 28 inch Bar and & one used Stihl brand chain (3/8 .050 91 Drive Links). Asking $65 + shipping SOLD Combo #2: Used OEM Stihl Chainsaw 36 inch Bar and & one used Stihl brand chain (3/8 .063 114 Drive Links). Asking $80 + shipping SOLD Combo #3: Used OEM...

ilm looking for a good used OEM piston for an Echo CS-590 or CS-600P (or Shindaiwa 591) . If you have something available, please let me know. Thanks.

This listing is for a used Stihl 038 AV Super Pro Chainsaw that needs some work, and is missing some parts. The pictured 20” bar and chain is included. The engine has good compression and will start, run and idle. I performed a compression test and got a reading around 163 psi. I also removed...

Looking for a couple of parts for a Husky 455 Rancher. The saw is well used, so like condition for parts is fine. Things I'm looking for: A 20" guide bar for .050 gauge, 3/8 pitch chain Top cylinder cover (need one with a cut-out for the purge bulb and screw down fasteners) Clutch cover - the...

I am rebuilding an Echo CS-600P, and can’t remember where this part was located. I see it in the IPL, but it isn’t clear where it is supposed to be placed. I had some issues with getting the correct crankshaft bearings for the saw, so that has resulted in having been about 2 months since I took...

I have an Echo CS-600P that I am currently repairing and there is some confusion somewhere on the crankshaft bearings. I just removed the old bearings, and was ready to install new ones, and I noticed the outer diameter is different. The new bearings are too small to fit in the crankcase half...

I have an Echo CS-600P that has scoring on the Piston, so I was investigating the parts lists and wondered if anyone has a description of what has changed about the CS-600 / CS-590 piston & cylinders over time. I see that the Piston & Cylinders used vary based on model & serial number ranges...

I'm looking for a good used OEM Piston & Ring from a CS-590 or CS-600P. If available, I would also like to have piston pin and needle bearing. There apparently were a few minor changes to the pistons over the years of production, but I believe any will fit. I would also consider purchasing a...

I am selling a Poulan Countervibe 3400 chainsaw that is in good physical condition. It is currently not running, and appears to need carb work to get going. It will run briefly with fuel mix poured down the carburetor throat, but will not run otherwise. The only thing I noticed that is not...

For sale is a Husqvarna 359 chainsaw. The saw is overall in good condition, has spark & compression, but I believe needs some carb work to run well. I got it to pop, and run a little bit, but it seems to be flooding. I removed the muffler and got a couple pictures of the cylinder. Through the...

I have a Husqvarna 359 that is missing 2 of the 3 clips that secure the top cover. Anybody have a couple of those clips for sale? Husqvarna part # is 503894701 According to replacementsparts.com these clips are used on models: 346xp, 351, 353, 357, 359, 435, 440, 445, 570, 575, 576 For...

I have a Husqvarna 359 that is missing 2 of the 3 clips that secure the top cover. I'm looking for a good source to get two replacement clips. Checking ebay it looks like it would be over $20 for two new clips. Anybody know a good source where I could find used (or new) clips cheaper? For...

I recently acquired a rough Husqvarna parts carcass that I was trying to identify. There are no model numbers legible anywhere I can find. There appears to potentially be a 2XX SE above the serial number on the ID tag. I've attached a few pictures. Any guesses as to the model number? It has...

McCulloch Pro Mac 850 Carb Question I recently purchased a McCulloch Pro Mac 850 from Craigslist, and was trying to check it out and get it running well. It has good compression. About 170 psi on my compression tester, and has spark as well. It ran to some degree when I got it home, but...

I have an Echo CS-370 saw that I bought used, and I've read what seems to be a variety of opinions on when to replace the drive sprocket. It seems that the manufacturer websites say after you wear out 2-3 chains, the sprocket should be replaced. I have also read that ~0.5mm wear on a sprocket...