Search results

Does anyone know if a cable that might be available for stihl 084 aux oil ** pn # 1124 640 9900 ** I am wondering why someone at farmertec or hyway hasn’t contracted a builder for this part. Seems like something that is needed! no stihl support for them has been in effect for years. Also would...

Yeah, sorry should have clarified

Thanks, I'll measure it up

Just realized you meant max flo...yeah we been running 660 kits an modifying them to fit. They actually aren't bad in regular timber but now in a burn the dust is getting through.

They do make one, the round lip on the back of the intake plate is perfectly round and can clamp right on there. I would argue that as a work saw it'll work better because you won't have to remove the divider to mount the filter. It won't be running a velocity stack so there won't be any gains...

No not yet, I was working on the intake and exhaust, opened up the bottom of the transfer. Lost the pressure switch on my compressor so I'm down for a little bit...I have the case split getting some crank work done. Is there a number I should target?

Huh, I've run them on my other saws and lots of guys I cut next to run them on their huskies. We never had a problem. It's a better option over the max flo right now. The max flo isn't held tight enough snd it's letting it in too much dust..

anyone have a part number for the kn filter that will work on the 661. The thing is begging for it and I'm sure someone has put one on. I've seen it. Instead of picking through the kn dimensions I hopped to get a pn from someone.

So with this new port design I'm trying to get some more flow. My question is specifically regarding the transfer ports. On the 660 I always went wider, never messing with height. I'm wondering if transfers can be opened up, height wise, and if that messes with "port timing" in any way raising...

Sure

The top plate fits most

It has a Zama carb on it but I plan on using a Walbro to replace it. I'm putting a 460 carb on it. So I need the plate for a Walbro carb. Sorry, I should have mentioned that. Is that number for a Zama?

can someone give me the PN for the top plate on older 044 Stihl carbs (and others) I need to delet e the "snorkel" on top of the carb. I can't find any numbers and I lost the PN. If this isn't making sense I can elaborate more.

Hey I found one last week too. Not as clean but in nice shape. Picked it up cheap. Going through it now. I'll g t some pics

Thanks guys, yeah i'll take that ipl, pm on the way. I'll just buy and nut and thread it LH on the lathe. Or get a Stihl...

Hey guys, I'm needing some help. I've looked high and low for an ipl for 075av. Specifically I'm looking for a source, part number, or size; for the nut that holds the clutch washer. So the drum goes on then the clutch then the clutch washer then finally th nut. I can't find a nut... It appears...

Cancel the pics, thanks for the offer. Thanks for the PN's it looks like I was given the wrong PN that I was trying to use. I found a used trigger with the above PN and I'll install it. Thanks for the info on the interchange between the 88 & 84! Thanks for the help guys, I was frustrated...

Ok I may have figured it out... So I look up the PN for the trigger and it gives me 1128 182 1005 (which is the same as the 46, 66 etc so: Either discontinued the old trigger and updated (standardized) to the above PN. Doing this you would also have to update to a different throttle link...

Thanks, that is how I have it but for what ever reason I cannot the the arm to engage the butterfly... If you happen across some pics maybe I can see what I'm doing wrong. I've got about 4hrs on it today trying to figure it out...Stuck...I'm not a master mechanic but i rebuild quite a few saws...