Search results

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. merc_man

    Carb gettin too much fuel

    Working on the little power mac mcculloch. Put new line on it. Cleaned carb. Tried to fire it up. barly stayed running wot. Pulled filter cover off and was quite wet. Tried pulling and can see the fuel spray in each pull. Got it running like that(bairly running) and it gives a heck of a mist of...
  2. merc_man

    stump grinder question

    I am gonna rent a stump grnder. Got one big stump and a few smaller ones. Just wondering if one of the smaller portable ones would work. The big stump is probobly about 30 or a little better inchs. Rest are 16 and under. i know bigger is better but would be easyer with smaller one. So whats...
  3. merc_man

    Good day to cut

    Out cuttng with my son and a buddy from work. Sent from my SGH-I747M using Tapatalk
  4. merc_man

    Cylinder bolts came loose

    was running the husky 353 today and it ran great then it suddenly went lean so shut down rite away. I rebuilt the top end probly about 15-20 tanks ago. Any how do you guys think i shouldbpull muffler and check cylinder? Should i do a leak teat toake sure i never damaged the base gasket? Mabe...
  5. merc_man

    Ms 250 bar

    Just wondering if you can switch the ms 250 from the small bar mount set up to the large bar mount. If i could, i could use other bars an chains i already have. Was thinking just switch bar studs? Not sure what thred size is for small and large for screwing into the saw. Sent from my...
  6. merc_man

    Dremmel tool sharpener

    Any body try the dremmel tool sharpeners. I have a cordless dremmel and was thinking of getting some chain sharpening bits to try in the bush when chain gets dull. Just thought might be quicker then filing. But i would still refile when at home. Sent from my SGH-I747M using Tapatalk
  7. merc_man

    What pitch is this drive spocket?

    Saw is a remington pl4 it came with a 3/8 pitch chain which i figure is rite for 59cc saw. The chain drivers seems not to mesh very well going aroumd the sprocket. I looked on acers chainsaw colector and it says it has a .404 pitch could this be rite? Heres a pic with part number on drum. Sent...
  8. merc_man

    Oil pump question.

    trying to get my sons saw to oil that he picked up. I tried blowing air back through the oil hole and mabe cause presure in tank it pump great for few mns then shut off and tried an hour later and barly anything came out. I pulled the clutch and the little drive gear looks ok. Threads are good...
  9. merc_man

    Walbro wd 247 carb question

    Just rebuilt carb with gasket kit. When done i tried blowing through fuel inlet and could blow write through and air came out the impulse hole on carb. Which just fills cylinder with fuel. I pulled carb back apart to check everything. All looked good. Just wondering what im missing. Did i blow...
  10. merc_man

    Forest king chainsaw

    Just wonderng if anyone has tried the forest king saw from tsc that comes with two bars and two chains. Looks like a good deal for a cheap little saw just to have. Sent from my SGH-I747M using Tapatalk
  11. merc_man

    Mighty vac 04000 question

    Just got a used pressure vac tester today. Was wondering if anyone else has this modle. I notice that the presure port dont register on guage only the vacuum. Was thinking of getteing a low pressure guage and plumbing in to the line off the pressure port to see if that will work. Anyone else...
  12. merc_man

    This is where it all starts

    I found my son his first saw this morning on kijiji for $10. All it needed was a fuel line filter and a chain. We got some.fuel line for it. A local auto parts place had a chain for it but was no good the cutters were all messed up. We got it running with new line. And will pick up a chain and...
  13. merc_man

    Stihl 026 pro carb adjustment?

    first time trying the 026 today. Saw fired up perfect let it warm up for few min or so then eased on throttle and dies. Few times of that and put it away. Get home and figured id tinker with it. Fire it let warm up and runs mint WTF. may have to clean carb put new kit if i do. Any how thought it...
  14. merc_man

    Ms 250 seams to run a little hot

    Just picked up a stihl ms 250. Went over it this am cleaned it sharpened chain blew out all saw dust i could checked piston cylinder all good. Took it out to bush to try and after 5-10 mins of running it seems to get hot. When i let off throttle ot would stall sometimes and a little smoke came...
  15. merc_man

    Pics of you favorite saw.

    This is my shelf queen just got a good deel on the 18" bar($30) and thought it would look good with it. Who knows mabe ill even bring her out next time. Sent from my SGH-I747M using Tapatalk
  16. merc_man

    Ya ever have one of those days

    Started out good all excited to go cutting. Get out ther start the 041 start cuttng off the limbs of a.hickory i already nocked down. Pinch the darn saw. Then forgot how heavy hickory is had to cut it n 6' section to be able to pull out of brush with atv to cut up that took way longer then...
  17. merc_man

    How to post videos

    Having trouble posting videos. i can get the picture directly from phone to here but not a video. If i cant do a video on phone to here how do you get it frm photo bucket to here. Do tou jave to use a computer? On my phone im using tapatalk. Thanks Sent from my SGH-I747M using Tapatalk
  18. merc_man

    Tach wont shut off

    Juat curious what tach you guys use. I bought one off ebay It wont shut off. Sent from my SGH-I747M using Tapatalk
  19. merc_man

    saw rpm question.

    I just got a tach to check saw rpm. (Saw is husqvarna 353) i rebuilt it with aftrrmarket top end. Original piston had one ring and after market has two rings. Factory specs say 13 000 max rpm. I check it and its only at 11 200. i tuned it by ear and seems to perform quite well. Gurgles out of...
  20. merc_man

    Nascar saw

    Didnt know huqvarna make a nascar addition 353. Cool saw but no way would i spend that kind of cash on a 50cc saw. Id be afraid to get it dirty. Sent from my SGH-I747M using Tapatalk
Back
Top