Search results

I had one of the 3 clutch springs break last week. What’s the secret to getting the new spring installed. Every tool I have to stretch the spring wide enough to get in the slot, the part of the tool is in the way. I did a search on here and online in general and did not find any help. Thanks

I have had this 262xp for about a year now. I have only run 5 or so tanks through it at my house for firewood; but it looks to be well used before I got it. Compression is 170 and cuts real nice with the 18” 3/8 on it. Anyway. I took it out yesterday to cut up some ash logs. Made about 10 cuts...

ordinarilly when I am using my woodmizer I will do a log or 2 at time. Then drive the tractor over with another log or 2 and take away boards. (One trip) I have the mill next to my house, so I drive across my lawn to do this. When I know it will be wet out, I may stack 5-6 logs so I don’t have...

Anyone use this chain. I usually use Oregon lgx but there is a deal online for 100’ of the Carlton a2lm. Would like to know a little more before I plunge into a 100’ if it. Thanks

I have a 2012 bandit 990 with the 85hp cat. About 1050 hrs now. Everything is good on this chipper all the time but the lift pump. My lift pump on the fuel filter went bad at 425hr, 850 hr, and acted yesterday like it went out at 1050hr. When you try to get a new lift pump from the cat dealer...

Looking for input on getting and electric chainsaw. I have a woodmizer lt15. I have the electric one so I can run and not make noticeable noise to the neighbors. I was looking into getting an electric chainsaw for cutting up the slab edges for firewood. I do keep one saw stock, a 2260, for...

I bought this saw new in the fall. Bought so the climber can use in the tree when needing bigger than the 200t, but not needing a 2260 with a 20" bar. But it doesn't get used enough. We used it a little on the ground as well, but not enough to justify keeping it. It's the only saw I have that...

These saws were given to me by an old timer recently when I did work at his house. He figured he was too old for them now. No real back story. They worked when he put them down last, he says. Which was years ago. They both feel like they have good compression, but that is about all the time I...

Recently put my order in on a bandsaw mill. I opted for the electric motor for the much less noise primarily. Doing some research for the electrical before I have an electrician I know come over to wire it, so I have an idea what he is talking about. Motor info is 10hp, 230 volts, draws 44...

Is this an easy fix. Just pulled off today.

I have 2 200t that I got late in the fall. They needed a few parts, but with winter coming, I got them with the idea of having them up and running when spring came. We ended up working till mid Jan and started again in mid February, so time ran too short. Saw 1 had 150psi when I tested it, but...

does anyone have one of these? How do you like it. There is one close to me for sale with the 65 duetz and the grader blade. I have a 97 rayco rg1642 with 42 duetz. Works good, but was looking into more Hp and self propelled.

Hey All, I have a 2000 372xp I picked up a couple years ago and use from time to time, the only completely stock saw I have. On this rainy day I figured I would check the compression and see where it is. It is about 130psi. Well, I had planned on modding the muffler, deleting the base gasket...

(since I know I have to order a carb kit for my 357x) I remembered that my 2139t has been sitting on the shelf for several years now and the last time I ran it, it seemed like the diaphragm was going on it. I am trying to take the carb off the saw. Do you have to take the handle and such...

I believe this saw is a 2008. It was my primary 20" saw till 2 years ago when I bought a 2260. Since then, it is a back up saw, which I basically run just enough to cycle the gas through. I went to run it last week and all of a sudden it didn't want to run right. Right now, it will start...

I have decided to replace my hotblast 1300 with a larger unit for our new home; we went from 1150 square feet to 2450. My hotblast worked great at the old house, and works pretty good in the new house down to about 30F so far. Unlike most of what I have read about them, by running the hotblast...

Hey Guys, looking into getting an indoor wood boiler. we recently moved from our 1150 square foot ranch, which I ran my hotblast 1300 with forced hot air. We now live in a 2400 square foot colonial, with a huge unfinished basement, not part of that square footage. We are going to be in this...

Hey all, I need to replace my starter pulley on my 2260; there are two pieces of metal that stick up that make the contact when starting the saw; they are bent and the saw is real tough to start as a result. I cannont find a part # anywhere on the internet. On a parts website, I found what...

Hey all, This is a stihl 028 wood boss electric quickstop model. The saw is physically in pretty good condition. This saw was mine for years, before I sold it to a neighbor when I bought a newer Husky to take its place. The neighbor decided to run a tank of straight gas in it, because he...

Hey all, I am wondering if anyone out there has one of these models, the 26 ton from ramsplitter horizon/vertical. I have been using a cub cadet splitter for years, I sold it and am looking for one with a faster cycle time. Their info says 8 second cycle time, with a 270 honda. The price...