Search results

That tree after blowing all the needles from around the base and cutting two major roots and maybe 8 more, Did not budge. I pulled until my tires were spinning. Nothing. So part B cut her down and that is what I did. So now I have a mass of roots and a stump to deal with. I'm thinking about...

In the morning I'm going to remove a 24 in dia. pine 10 ft. from my house. I could cut it, it's already leaning in the direction I want it to go. But, I want to remove the stump too. So, I'm going to put a 3/4 or 7/8 arborist bull rope 20,000 lb breaking strength thru a major crotch about 15 ft...

Panasonic makes the best !/2 in drill. The 14 volt lithium . is as powerful as the others 18 volt I use mine every day. I open and close a lathe chuck with it set on 17. The impacter has 3 settings and it is my go to impact gun. For the hard to get to places I bought an Hitachi right angle...

026 carb replaced I replaced the impulse tube and installed a Walbro wt-194 that I got on eBay. I removed the snorkel cover from the original carb and mounted it on the new Walbro wt-194. YES! I finally have a almost brand new 026. Thanks for all the great postings on this site. I felt like I...

026 carb replaced I replaced the impulse tube and installed a Walbro wt-194 that I got on eBay. I removed the snorkel cover from the original carb and mounted it on the new Walbro wt-194. YES! I finally have a almost brand new 026. Thanks for all the great postings on this site. I felt like I...

SUGIHARA 24 light on my ported 046. This is a great combination. The 32 oregon I have for it makes it very nose heavy. Wiz

I put a 20 in Sugihara light on mine and it is Great. I also use a Stihl RS chain. It had an 18 in. Stihl but I found it to be a little short. Wiz

Ordered a Zama Carb kit for my 020T. my 046 came out great so I'm going to try the 020.

Rebiult the Carb When swapping out the gas tank on the 046, I thought I'd blow out the carburetor. Wrong! So, I just replaced all the torn membranes that I wrecked by blasting the carb. It started on the 1st pull. I do want to change the pull handle either to a new elastostart or one of...

It's ported! I just changed the gas tank for a new one. So I took a look at the intake port and It's ported. The Serial number is "+139265230" The plus mark is turned slightly . If anyone of you Port Modding Tuners knows anything about this saw I would appreciate any info you could...

046 24 in Sugihara light, Stihl full skip RS chain. Man, This saw is amazing, I LIKE IT! You have to say it like the guy in Robo Cop after he shoots the 50 cal. Cuts through 24 in logs like a hot knife through butter.

I just ordered 24 IN 50 Gage 3/8 Sugihara light bar for it from HEV. .88 lbs lighter than an ES Bar. I went with the 24 because in a pinch I can put it on my 036 Pro. it is also .11 its lighter than the E bar. Wiz

I have it working! Wow! I noodled a bunch of rounds. But I need to get into something Bigger. Lots of torque. I bought a new gas tank in case the patched one leeks, so far it's fine. I also got a new Stihl 3/8 RS chain for my 036 PRO, Oh Ya! what a difference that made. Wiz

The new tank did not arrive. But the clutch springs did arrive and that tightened the clutch up nicely. The new clutch drum was the wrong one. Dealer is reordering the right one. The outside dawg is correct so now I have a chain catcher. Wiz

ok, I'll have a bunch of new parts next week for the 046. Ordered springs for the clutch. I then discovered that the springs had worn groves into the side of the holes the springs go through. So gona have to get a new set. I could put a tiny bead of weld in the groves and tighten it up, but, I...

I was perusing the Sugihara light weight bars. The 20 and 24 in are high on my list. Or Stihl ES 25 ES 20. That way I could run them on my 026 PRO, 036 PRO, 046. Does the driver width 50, 58, 63 increase the Bar thickness? Bar weight? Wiz

The Bar cover arrived today! It has a little chunk missing near the rear but when the rubber chip guard gets here that will cover that. I finally mounted the 32 in bar and chain and fired it up. Holly Cow! My that's a Big One. My Nick Name for this saw is "Junkyard Dog" . I definitely need to...

I asked the seller on eBay, why it is red and not yellow? It does look nice even though the color is wrong. Wiz

The guy I bought the saw from said he mailed it today"it's Sunday" The cover is most likely junk, but it should have the other spike on it. Anyway, I May have to get new large cover and the rubber chip deflector for it. Wiz

The Stihl 150 is listed in the pro tree saw section. I watched a u-tube video off someone using it. Very smooth cuts. Wiz