Search results

Phase separation. Use it immediately or face headaches. Store empty. And it's about pumping politics. Unless you're a moonshiner..

I'm working on mine. Clearing 5acres. Pit should be 20ft diameter.

Decided to sleep with the trees. My backyard. Shower, stove, and roof is a 3 minute ride in low range. Finding public, state, anything besides your own to winch is difficult. A LOT of young trees can be destroyed, along with ruining a nice lumber log with a nasty bruise. Some guys don't care...

I emptied gas out of a f800 that was probably 15 years old easily. 10-15 gallon or so. It was once or twice again darker then yours. Almost like mud brown. I think it was probably rusty dust mixed with gas. I didn't care. That's what filters are for, right? Poured it in the old trusty '98...

https://www.tractorbynet.com/forums/owning-operating/388515-4-wheel-drive-tire-ratios.html Also this is why I chose to use a full time xfer case with loc/no lock, instead of a cheezy chain/part time locked xfer case, for my mini loader. I used 3/4 ton steers, orbital valve, and a hydraulic...

Oh yeah. Maybe. That drott 4in1 is an ass saver.. Question. Old faithful was about 46 overall height, . This bandaid tire is 49.75, sadly it's not a 12/24, it's a 13.24, so, some math... Shows 1.08 difference.... I used a straight edge and square to get a accurate as possible comparison...

Found me some 13 24s. Set of 4, 16ply. Apparently someone has a used 12, but in such slight hopes, and this matching set that'll fit the hough 50 along with this Allis , I jumped on it. Now I need to finish making that bead buster... Where's me beer?

Local Vendor calling around is telling me that size is only available in a L3/E3. When they're calling it an R4 On a machine with planetaries that (might) be brass, but I know brass pins, how risky is this in the dirt? As mentioned, I know the differential are open, but double checking, the...

Carb wasn't adjusted quite right. I got it sorted. It's actually a stock old 60s out of my dad's road runner. His lovely wife smashed his car few times, so after totaling it, he ripped it out and stuffed it in his Allis Chalmers after the Hercules injector pump went goofy and over revved...

Machine has open differentials, so an inch of difference playing in the sand and soft ground shouldn't be too stressful on planetaries/driveline. Driving sorind country side I did see a huge tire leaning against someone's house. And I thought to mark it on my Gmail/maps account and didn't. Err...

Yeah I don't know. Yesterday evening after the rain I looked at it closer. I don't think there's any good tire to anchor the repair against. Waiting calls on a used something from various vendors. In the meantime there's other stuff to do. I got the yard and building repair excavated enough...

Thread closed. Found me a $30 fix. Here we go!

Yup, need one. Can be completely bald, so I assume cheaper, , just no gashes or tears. I'm rubbing tubes and chains, so I don't care of bead sealing or traction. Im out in grand Rapids MI area. Ill drive 200 miles.

Oh man. I showed her the reply and said *******.

Where's/how to check trans fluid? I've been blindly adding daily, as the steering is part of the same circuit, and that cylinder leaks terrivle. Thanks.

Yup thanks. I started another thread on another engine. Slowly getting things back togrther.

Spoiler, not a chainsaw. Chrysler 318. Timing is splitting a hair dead on, new plugs, wires, cap, rotor, coil, vacuum advance works, condenser,.buffed points. I ordered a China 2 barrel factory like replacement carb. When really working it hard I get nasty yellow flash Bombs out the carb...

Apparently there's also something bad in the switch. Oj well. Learn

I so assumed the obvious.

It runs! The f'in test lead I cut off this roll has a break in it. Some roll that's been around since the 70s. Haha. Damn.