Search results

I don't recall all of the parts that came back. I'll have to make a list if these saws become popular again.

Purely for science,since Modifiedmark has what you need, here are a few pics of a BP655 reed block. Without measurements they don't have much value but if anyone sees any noticeable difference chime in. I know I've sent some 655 parts out to people who were needing it for their P60 or P62 and...

Can anyone confirm or deny that it's the same reed block as the Poulan 655?

Since I woke up in the middle of the night I figured I'd do what any sane person does at 1:30am on a Saturday; try to find a better carb for the echo 620pw. While looking at my favorite Irish website I saw this: Look familiar? I thought I saw one with an orange top cover once.

If you already have an Oregon Powermate sprocket with a rim that is 3/8ths you are good to go. If you have a .404 rim all you need is a 3/8ths rim. If you have a spur sprocket that isn't the correct pitch you need an Oregon 22132X Powermate sprocket and 3/8th's rim. As far as the screws, check...

Well, I had some time and swapped the new spider for the old, put a bit of 680 on the shaft and tightened it up. I let it sit for a few days and fired it up today. Works great. I made a few cuts on a 36" madrone with my tiny bar and got depressed. It's been a long time since I've had to cut...

From burnses description I may have the wrong guide disk. Is the sprocket bearing bushing supposed to fit through the guide disk hole and contact the clutch? If it is that means I have a 152 guide disk, because the hole is not large enough for the bushing to go through. If the bushing does need...

It took a while to find some lapping compound. The only stuff I could get is water based. I've never used it before, only grease based. It will be this weekend before I will get around to testing it. One further question: Has anyone used Loctite 680 on a saw clutch? Good experiment or bad idea?

Thanks for the reply's. I am not a fan of this saw and hope I never have to pull the flywheel. I got it because it was the only 6 cube with an aux oiler I haven't tried. My 2100 is getting tired, and I truly dislike the 655 BP, I have some long bars from an 084 I used to have so I thought I'd...

I have no idea if the washers are correct. There are no part numbers on anything, and you can't trust the bay. I have several sprockets that were sold with the correct part number listed, but were 19mm when they arrived. Here are some pics of what I have going on. Sorry about the focus, the old...

The nut was torqued to 19ftlbs. It has the proper shoes, as far as if it is the proper spider, I don't know. It measured out the same as the old one, but nothing on the saw was to spec when I got it. If there isn't a specific technique to installing the clutch I can put the new shoes and spring...

Is there a secret to keeping the clutch on a 153? I had a new clutch put on and it will not stay on. The original sprocket was incorrect for the saw, so I got a new bushing, new bearing, and new sprocket and new clutch spider. Still no luck keeping it on. Not sure about the first try, but the...

I ended up blocking off the compression release with a plug included in one of the kits, it enables me to start the saw, but it was never on the first pull. Or the fifth. I read your old thread, and saw I responded to that as well. I forgot about the NWP kits. The kits I tried later all had...

Have you checked the compression? The first BB I put on my 6401 gave me 110psi and was nearly impossible to start. Checked squish and with a gasket was .059. Some of the aftermarket kits are just not that great.

New MS660 http://oregoncoast.craigslist.org/tls/5150872794.html

I still have everything, and it's still for sale. As a package. Unfortunately, this is the first time I've been able to log on since January. I can't guarantee I will be able to log back in later, pages keep timing out. At least the pictures are still up and working. If anybody wants the saw...

It is still available.

A couple P42's. I wouldn't mind getting the v-stack off of one, but I have no use for the rest of it. http://roseburg.craigslist.org/tls/4841559238.html

A post Christmas bump. Why ring in the new year by blasting off a few fireworks when you could wake up the neighborhood with 6 cubes of Americana? With a subtle shout-out to our Canadian cousins, of course.

Price drop to 600 GBP is 1092.06 CAD 943.02 USD. Do you have pictures? What are the shipping options?