bar

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. S

    Finding Long Bars

    I've spent lots of time looking for long chainsaw bars to fit my 070 and haven't found many options. Seems that most manufacturers stop at 42" or so. I'd like to find a 36-38" bar, a 48-58" bar, and a 72"+ bar I'm aware that the 070 and 090 need either a special bar or custom drilled holes for...
  2. L

    Want to Sell 07/98 Stihl 066 with a ton of extra equipment.

    I have an 066 chainsaw for sale, with TONS of extras. 4 bars, 3 brand new and 1 used. The bars are as follows; 1x36" 1x28" 1x20(new) 1x20"(used) 12 brand new chains--Assorted for ALL OF THE BARS. Files Sqrench New carb, air filter, spark plug, ignition module, fuel filter. Asking 1900.00 for all...
  3. I

    Husqvarna 3120XP - Chain Locking Up

    Hello Chainsaw aficionados, I recently got a secondhand 3120XP in basically new condition with no bar and chain included. I've been working on procuring a bar and chain for ripping with an alaskan mill and I ended up with an Oregon 363RNDD009 bar (3/8", 0.063", 115DL) and an Archer ripping...
  4. Howard Justice

    Stihl 201 CEM BAR/CHAIN?

    We are most fortunate to have a new Stihl 201 donated to our Disaster Response Team. Saw will always be on the ground - primarily limbing. All our work is at ground elevation. Came w 14 bar. I would welcome suggestions on best bar and chain for that purpose. Thank you! My goto saws going fw...
  5. I

    Help Identifying Chainsaw Bar

    Hi, I have a 24” and 36” bar that I received when buying a used 3120XP. I think both are Husqvarna (the 36” came in a Husqvarna cardboard sheath), but neither has a company logo or any naming on the bar itself. The 24” bar had a chain already on it, wrapped in plastic. I’d like to understand...
  6. Y

    MS361 Bar and Chain Question...

    I just bought a nice MS361 from a fellow who had a 20" bar on it. I want to put a 24" or 25" bar on it, Rollomatic, the extra light version if possible. I would also like to try a ripping chain and a reasonably aggressive crosscut chain. My current 026 has a chain with a yellow mark on it and I...
  7. Bag of Nails

    .50 and .63

    Can you run 3/8 .50 chain on a 3/8 .63 bar? Would the chain be loose because its not thick enough
  8. F

    MS261 bar and chain changhe advice/ideas

    Hi, My current bar and chain are knackered so I am getting a new set. It was a second hand machine with an Oregon 18" bar and .325 chain on it. The standard route would be a Stihl rollomatic 18" 74DL with a Stihl .325 RS chain. This is factory settings so to speak. I run a small property...
  9. S

    Counterfiet Sugi Hara?

    I got this carving bar. It is supposed to be a sigh hara but looks nothing like any of my other such hara bars. My reasoning is that it is stamped I am pretty sure sugi hara is machined. Also totally different logo.
  10. big hank

    Want to Buy 50" - 60" Large Mount Stihl Bar

    Looking for a bar for my 084. Figured I'd ask here before I bit the bullet and bought new. Willing to pay the right price for a nice used bar Thanks, Hank
  11. S

    Want to Sell Like new Stihl 25" large mount .404 .063 bar and chain

    I have a 25" large mount (3002) bar and chain in like new condition. I purchased this thinking it would fit my MS660 and apparently I was wrong... I do have an 880 that I could put it on but I already have a 47" and 30" bar for the 880 and don't really need another smaller bar for this saw. The...
  12. H

    bar identification

    hello all, i was recently given a 48" cannon bar. it used and probably 10 years old but its in fine shape. it is marked "HUS5063 S" i dont know if this means i need to run 063 chain or not. its for milling mostly and accational stump job, if you understand these markings please help. thanks
  13. N

    New chain for Stihl 261 questions

    Long time reader, and student of the arborist site, and normally find my answers already posted, but I searched for this one and couldn't find a clue, so here goes. I have a 261 with the standard sprocket and a 20" green bar. standard 325 chain. I need to replace a couple chains that are a few...
  14. T

    Homelite C-51, ignition, and bar selection. In the correct forum now.

    Hello, just created my account. Decided to come down from lurking in the woods to the warm and tidy campfire that is arboristsite. I just recently purchased a nonrunning Homelite C-51 convertable drive for $10. The two main problems with it are it has no spark, and the 20" windsor bar was...
  15. T

    Homelite C-51, ignition, bar selection

    Hello, just created my account. Decided to come down from lurking in the woods to the warm and tidy campfire that is arboristsite. I just recently purchased a nonrunning Homelite C-51 convertable drive for $10. The two main problems with it are it has no spark, and the 20" windsor bar was...
  16. J

    Olympic 240 bar replacement

    So I went to Lowe’s and got a Oregon replacement bar/chain combo. The oiler hole didn’t line up, so I drilled a hole lower than the original Oregon one and drilled down from the channel to the new hole. The bar does get some oil now, but is that enough of a fix? Is there a bar that anyone knows...
  17. M

    Echo CS-800p setup for milling?

    Just picked up a CS-800p with a 2o" and 36" bar along with a few chains for $225. Ive got a 36" granberg mill that I've been using my cs-590 with a 27" bar on, but it tends to struggle. I'm still relatively new to this so I thought I'd ask the experts... First... Are there specific bars that...
  18. D

    Looking for large mount bar 42" 3/8 .063

    Looking for large mount bar 42" 3/8 .063. So far I've bought 4 bars on eBay the people claimed were large mount that fit Stihl 070/076/084/088/ 090/ and MS880. Everyone of them has been the small slot for the smaller saws. Getting VERY frustrated. My 36" bar is too small milling and need a...
  19. MattLinq

    Used Stihl Chainsaw Bars

    I was looking on the tradin' post this morning and noticed someone was selling a 25" and 30" .404 bar for the larger Stihl saws and there seemed to be some sparked interest and they seemed to have sold. I was wondering what a guy thinks he could get for a used Stihl bar and what ones are worth...
  20. F

    John Deere CS56 bar/chain woes

    I have a JD CS56 that runs like a dream, is strong and very reliable, despite my novice knowledge of maintenance and lack of upkeep... Only thing ive done in the three seasons ive owned it is put a primer bulb on it and keep oil/fuel in it. Cranks on first pull and runs like a top every time...
Back
Top