husqvarna

Hey fellas, I opened up my new 445e muffler a little bit (drilled Two 1/4 inch holes and removed spark arrestor) I have the tool to adjust the carb. I believe I have it four stroking and it cleans up well in the cut. After a few hard hours the plug looks pretty lean, if I back the H screw out...

I bought a 565 today and while looking it over i noticed quiet a large crack in the intake boot. Hope you can see the crack in the photos, how many of you have seen this on brand new saws?

I bought a 565 today and while looking it over i noticed quiet a large crack in the intake boot. Hope you can see the crack in the photos, how many of you have seen this on brand new saws?

This is the second time this has happened to me on this saw. The first time my dad put straight gas in it. It looks similar and I used acid and sandpaper to clean the inside of the cylinder and just added a new piston. It wasn't perfect but it looked pretty good. I am wondering if this...

As a newb, I’m insanely confused with all of the “oil” options out there. I have a Husky 440. As for fuel, I’ve been using a store bought pre-mix (I’m ordering Husky brand pre-mix just to be safe). I recently bought Husky brand bar and chain oil. HOWEVER, the small print on the back scared...

FS Jonsered 2253 with the MMWS treatment. The saw has less than 1 hr of runtime according to the dealer who updated the carb software in Sping 2019.if you’re not aware of this model it’s identical to the 550xp MK1 but just in red. $750 Shipped Paypal F&F to your door if you live in EST, CST, or...

I just closed a deal for €110 for a second hand husqvarna 372XPG. Is it easy to work on? It looks like it's been neglected for the past few years, probably needs some attention. I know how to do th basic things to a saw, carb, spark plug, cleaning muffler etc... Any tips? Thanks in advance, Jan

2004 Husqvarna 55 Rancher, big loss of power in cut, RPMs drop. Chain sharp, tension adjusted. Fresh fuel. No smoke. Figured I had the carb. mixture mis-adjusted, I riched out the H screw a little at a time to about 2 turns out from seated. I removed mixture screw limiters a couple carb...

I am interested in making my own base gaskets for a couple of Husky 350's that I am rebuilding. What would be an appropriate gasket material for that? Thanks in advance!

I have spark, I have fuel. I have 130lbs compression with just 3 pulls. I have gapped and I regapped and regapped the coil/flywheel... Mind you, I have good blue spark when I put the plug in the boot and ground it on the cylinder head. Put the plug back in and try to start it I get nothing. I...

Anyone feel like chiming in here about any tricks to get this back together? The mechanism is extremely stiff and I can’t get the brake to pivot as soon as I put the cam pin in. I’ve searched for videos online and found one about a 55 but it’s not the same. This is a circa 89/90 era saw. I had...

Hi guys, I saw yesterday on FB that Patrick Lacey had an unfortunate run in with a dirty rotten snag on the job and is currently laid up. From the sound of it it was pretty bad. He is not looking for donations so I figured I would take a cue from his buddy that posted on FB and try to get as...

Clean Husqvarna 254xp, Runs good. Piston and cyl are clean. Comes with bar and chain pictured. Saw is NJ for pickup or can ship pretty reasonably. Asking $400

Maybe keep engine cooler n combusting better. I know most cutters live in a cooler climate. But in a hot environment? How can extra cooling be a bad thing. Especially on a completely closed air box, with an engine I expect to perform n create heat. I might go a bit bigger hole n line the...

Title pretty much sums it up and I've done the research on HOW to do it. Still probably going to get stuck lol. I was wondering who out of you have handled a ported 346xp, I mean out of the box the engines rpms mac out at 14,500 which is already insane. Curious on your thoughts on the project...

New crank bearings, gaskets, seals, oem piston, rings. Runs and oils as it should. It does have some blemishes but should be a good runner. Would like $375.00 shipped to you.

Hey guys. I'm Matt. I've been working for a trail crew in Utah and enjoy the saw work immensely. It has given me the spark to finally try to get this saw running. I got it for free from a ski resort firewood crew and was told main bearing was bad. The further I got into the saw the more problems...

This one has new skf bearings, oem piston & ring, gaskets, and fuel line. There is one hole that i repaired with a time-sert. As you can see the muffler is getting thin and there is a crack in clutch cover. This saw has not been in wood yet. Would like $425 shipped.

Yes another 385xp! This one has new Meteor piston & rings. Pull rope & steel insert along with carb kit. This one has been started, warmed, adjusted and rpms checked. Setting are set rich at this time. Havent had in any wood yet. There are some signs of wear as this is not a NOS saw! Anyway will...

Hello all, I'm new here so my apologies if this isn't in the correct spot. My question is what a good condition husky 365 is worth? I don't think it's a special but I'm not sure because the sticker was removed. Thanks