husqvarna

Forsale PHO. Saw has one tank on new rings. There is some scrapes and bruises as you can see. Some retard thought he needed to scratch his initials on clutch cover. Can swap full wrap for half if wanted. Asking $435 and ill pay for shipping.

Saw has carb kit, new piston rings and top cover. Has about a tank of fuel since repairs. Muffler is dinged up a bit. Selling as PHO! Will cover shipping to lower 48. Would like to get $450.00. Will swap out full wrap for half if wanted. Just added piston pic!

HI all, first post for me here although been lurking for some time. I have a very low hours 480CD that I use for occasional milling- mostly canting larger trees in the woods that i cant get my bandsaw too. I have basic knowledge of porting 2 stroke engines- mostly high performance...

Hello all, new user to the site, have lurked some forums. What a great place. Lots of helpful advice and tips. Little back ground. Husqvarna 254 professional serial number 8180663, I seem to have a dead coil. Saw is ancient but I love it. It rips! Compression check 130 psi cold 145ish...

Hey everyone I'm new here. I have a husqy 435 that I have almost decided to set on fire. I never could get it running right. It had odd intermittent starting issues usually when hot, then all together. I tried all the usual suspects. Put a new carb on, new vent filter, new fuel filter, new spark...

I have a husqvarna 365, bought new this year. I have been milling slabs with it using an oregon 28" bar, trying various brand ripping chains. I have some great timber that is too big for the 28" setup (max cut width ~23"). Will my 365 be able to run a 32" bar and chain (max cut ~26-27") with...

Does anyone have a detailed picture or diagram of a husqvarna 36 carb and how it is installed? Mine is apart and I cant remember how to put it back together. Specifically the choke and throttle levers on the right side. Cant figure out how the spring and stuff goes back with the choke lever...

The impulse grommet on my Rancher 55 is worn beyond use. I live in Chile and the local dealer does not have the part unless I also buy a new cylinder (at a ridiculously high price). A new one from the States costs about $7, but the shipping is about $35 and import duties add some more. I can...

Husqvarna 455 Rancher. Starts,runs,cuts as it should. $285 shipped in lower 48. Compression 150 psi.Powerhead only in shipped price. Bar and chain can be negotiated in deal. Make me an offer.

Hi, Just got this little beauty Any experience?

Was it on this site or was it somewhere else where an experienced saw mechanic offers to rebuild any saw, test it replace small parts and send it back to you after you send him your saw for like 200 or $250 the only thing that's extra is if it needs something major the guy sounded legit but I...

Fishing expedition. Anyone in Australia with a junk Husky 154 or 254 they're keen to dispose of?

Hey friends, just felling a dead tree which has root rot. I'm fairly sure that this tree has root rot but can someone confirm that? Seems like there's root rot and spruce beetles both killing my forest :(

I've searched and searched and haven't found an answer. I'm sure it's an obvious one but I want to be sure before ordering. I have a 55 rancher I'm fixing for my brother and the clutch is very rusty, I was assuming a new clutch would be good if they are cheap. The one that I found right of the...

I have the left overs from a Husqvarna 371K cut off saw that I converted. What is in the pics is what you get. It's a 14" set up. The date that I found was 2006, and yes some sites don't show past '05. Was taken care of, used for concrete work (abuse enough!). $75 + shipping. Will not separate...

https://eauclaire.craigslist.org/grd/d/arcadia-husqvarna-3120xp-chainsaw-24/6806653714.html Seems reasonable...

262XPG - bought from across the pond in rough shape. Top end rebuild including meteor piston, caber rings, seals, fuel lines, removed base gasket and bearings all done by a reputable builder. Put in the KS cylinder and 87 carb, both of which came from a member here. The saw is not ported and is...

This is my brother in law's saw. It is a Dynamark 39CC saw. Not a whole lot of information on similar saws anywhere. I've seen in other threads that this saw is basically a rebadged Lombard saw. Anyone have any info on approximate year or bar mount? I thought I seen somewhere that it was A061...

I'd like to buy a brand new 70cc saw with a Mahle cylinder inside from the dealer.I'm interested in the new saws,572xp and MS462 and to be honest,this is the only thing I'm interested in,having a mahle cylinder.Wouldn't mind a 461 or 441 though. So,what do you guys know,which one of the...

So I recently came across a 372xp and I've been very excited about getting it running. I got rid of my faithful 441 and I always compare the two saws. The 372 seems like it has a better stronger engine (I see it compared to the 462 more). But besides the engine, the 441 seems way better...