ms460

Hi Folks, I'm selling my MS460. It's a (almost) complete Farmertec engine assembly with the rest being OEM. It's also waiting on a OEM piston kit (just leaved Australia). It hasn't seen any wood, just ran to set up the carb. Powerhead only Asking US$500 + postage from France Works perfectly...

My 460 is showing a bit of rust on the stock muffler. I figure if I replace it, I might as well upgrade it. I've never done anything but run fuel & oil through this saw. Totally bone stock. It is about a 12 year old saw now (I think. close enough) The mod that always pops up is "dual port...

I'm having a heck of a time trying to find the tool to install the Fly Wheel side of crankshaft. Can you just press it together with a shop press or will that bend the crank. I have the pto side tool to pull the crank into position, just can't figure out the fly wheel side. I don't want to...

Just bought a MS 460. I'm going to have a 28" bar on it. I occasionally cut some oak for my smoker and lots of folks around here seem to be scared of tackling a larger tree (even when it is on the ground). I was tired of doing it with my MS 290 so I got a slightly more big boy saw. What sort of...

I know it's a long shot, but worth a try. Since I got my 261, the 241 sits in a case. I really want a 460 or 461. My 241 has a modded muffler and less than 4-5 hours on it.

$30 shipped

Stihl MS460/461 Rescue Kit. $50 shipped in the Continental US not including anyone in the PST or International (will provide exact shipping quote.) PM if you have any questions!

I have recently taken the saw apart to see what was wrong with is and it turned out the be more than I was want to deal with it needs completely rebuilt so it is being sold as parts $40+ S&H Would trade for case gasket and or seals and bearings for a 576xp and or ms460/ms461.

Mainly looking for a Gas tank. Just let me know what you have.

I just found a REALLY nice unicorn and I have decided to sell my MS460 Magnum. All OEM & very clean as I hope you can see from the pictures. PHO w/ dual spikes, roller chain catch, decomp plug, OEM HD filter and Stihl Pre-Filter band $635 includes shipping w/ insurance via FedEx Ground...

Looking for a Stihl 70cc size chainsaw and narrowed it down to these models. I already have a 372xp but want to try out a larger Stihl (have a 026pro). Saw should be all oem. Not looking for rebuild. Doesn’t have to be a show queen but not one beat to crap. Let me know what you have. Thanks, Joe

Looking for an oem cylinder for a ms460.

Huztl has a sale going for $26 + shipping. My shipped price is $36 to Oklahoma. Wish I needed some but if you guys need them get them ordered today. Huztl sales never stay priced as long as the website states...in this case it will not be $26 for 7 more days as the site shows. Make Chips!,

Let me just start off by saying I am by no means the best at sharpening, however I am getting better ;) check it out, the top half is before and the bottom half is after. This is my Demonstration of file depth under the top of the cutter. It allows for a better bite and a less immediate...

I have a nice ms 460, I would like to order a set of spikes for it, what is common to be used, and also do they all come with the roller chain catch?

Good shape MS460, all OEM as far as I can tell. Picked it up locally a few months back and have cut with it. Fires right up and runs/oils as it should. 150 compression, has the stihl OEM dogs and covers. Muffler port has been opened a little but internal baffles etc are all there. Comes with a...

Picked up an old 046. I checked the compression and it was at 90lbs so I recently replac d the piston/rings, coil and rebuilt the carb. It started up with some starting fluid and idled but kept bogging and dying when I tried to throttle up a bit. After about 6-7 times it stopped running all...

I need a used bar 36" and chain too if you have one. If you have pretty worn one I could get cheap that would be great. Need it to cut logs up in the river now that the water is finally dropping down. Don't want a new bar for this job

Patient is a 460, melted piston/cylinder. before disassembling top end, did a pressure test. the oil seal is leaking like an SOB, I'll replace. Also noticed that air is leaking out of this screw hole (oil pump mount screw hole, clutch side). Is this normal, the screw just plugs this leak...