ms880

Only about an hour of run time since I went through it. Has been modified, can swap it out for a stock cylinder. 195psi compression, new pro safety dogs, new clutch cover and new poly flywheel. Has a 461 coil with 880 leg to bring the rev limiter up. $1600 + shipping

I bought an ms880 a while ago, my mate is repairing it, tried replacing parts in the oil pump but it didn't fix the issue, he reckons it's possibly the pipes or something deeper internally. I originally suspected that the pressure from the engine was forcing out the oil. It really does pump it...

Brand new take off Stihl spikes with hardware and roller. $25 plus shipping.

I have a 25" large mount (3002) bar and chain in like new condition. I purchased this thinking it would fit my MS660 and apparently I was wrong... I do have an 880 that I could put it on but I already have a 47" and 30" bar for the 880 and don't really need another smaller bar for this saw. The...

Hello all, I am planning on stabbing logs. These would be Central American hardwood species and some, like guanacaste, are upwards of 72" wide. Not all are as wide but all are at least 36". I plan on using a 72" Alaskan mill and considering a double headed bar and my question is at what point...

I finally found some ethanol free gas. The 044 I finished runs fabulous on it. Better than any saw I've built. I need to try it on the others now. Working on the 084. I wasn't going to put bearings in it but decided to anyway. Magnified examination found wearing spots in both crank bearings...

I'm new to this site other than coming here to read old posts when I need info that I can't find elsewhere. So I'm not sure if this post is going to be in the right place on the site but here goes nothing. I have a Stihl 090 that I purchased and was going to use it for milling but before I had...

looking for a 660/880 or 395/3120 project saw.im located in Ireland so shipping is a must , pm me any info Thanks

HUSKY 3120 XP W/ 48" .404 CHAIN COMPLETE GROUND UP REBUILD!! Completley rebuilt from the ground up. All OEM parts only.! Crank case bearings and seals Complete gasket set Rebuilt carb and fuel line Near new OEM top end Many small parts , nuts and bolts Drive sprocket Pull rope and handle...

Low Hour MS880 I took on trade towards another one. I swapped the Clutch Cover & Air filter with the one I traded. This is the Air Filter Cover: $1,100 shipped PHO. I have a couple bars & chains if wanted.

Looking to see what is out there. Thanks!

Longtime lurker and new member here! I'm finally moving to a new property where I have a use for some big saws (and an excuse to get my dream saw) Looking for two saws. First, 880. Stock or work modded (not race) ~24" solid and ~42" lightweight bars preferred, but I can always source those...

Hi, new member but not new to the site! I've read about a couple ads with an 880 that were bogus and hope mine doesn't fall through the cracks! Selling my 880 with 41" bar and 2 chains. Purchased brand new and not run as much as I'd hoped, (still has all the paint on the bar...) and runs...

So I am seeking advice on what chain I should run on a 41" bar for an ms880, Stihl says the .404 will be the only fit they offer and 3/8 will not work. So will .404 be my only choice? Thanks

Fellas, I have some gargantuan Oaks to fell eventually (5'+ above the flare) and will be needing to slab them where they fall. I'm thinking with Huztl 660's being so nicely priced that a two powerhead 5'-6' cutting capacity bar might be the way to go vs an 880 or equivalent. That would be 14+...

Hello wonderful and insightful members of Arboristsite! I have lurked around this site for a short while now and am only recently getting pretty serious about chainsaws. I have read a lot of great information on here from all of you and it has gotten me out of, or rather avoided, some...

I have a Stihl 59" bar and chain for sale. It was only used to drop one tree in my yard. It came off a new stihl ms880 magnum. Make me a fair offer.

Hi there. I'm looking for a runner or project saw (3120, 880, 088, 084) I can turn into a hot saw for timber sports. My budget is anywhere from 0 to 400 bucks for the right saw. Hopefully closer to zero... :) Thanks. And if anyone had any advice for how to go about this I'm all ears