60cc Awesomeness, who is king?

Rugged made
shop deals on amazon
Treestuff
Advertise with us
Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
chipper1 said:
Even that has variables, but it should give a bit more accurate comparison. It always helps when everyone is open to a saw other than their champion winning, if not the whining about this condition and that chain or fuel... always happens.
Click to expand...
From everything I'm gathering it sounds like you may have already been to an internet GTG with the OP. I hope it went better than the people I've talked too's experiences.
 
Maybe I was misunderstood about the dyno. Repeatable within itself but not so much from one to another. So in other words, good for you to test a couple of saws on your dyno, maybe not so much if I test one on mine and compare with a saws numbers from yours.
 
SmellyPirateHooker said:
Maybe I was misunderstood about the dyno. Repeatable within itself but not so much from one to another. So in other words, good for you to test a couple of saws on your dyno, maybe not so much if I test one on mine and compare with a saws numbers from yours.
Click to expand...
The Dyno" Charlie" at ADM has a "Gismo" that will give comparisons to equalize conditions for the running of multiples runs of the same motor at different days or a different unit ,it converts the readings to be all at the same condition parameters ,knowing the unit cost I don't think Frank is in a position to shell out that amount of $'s with the apparent size of his outfit
 
Little Al said:
The Dyno" Charlie" at ADM has a "Gismo" that will give comparisons to equalize conditions for the running of multiples runs of the same motor at different days or a different unit ,it converts the readings to be all at the same condition parameters ,knowing the unit cost I don't think Frank is in a position to shell out that amount of $'s with the apparent size of his outfit
Click to expand...
Yah , this Saw is at 5.8hp which is .2hp less than a stock 461 or a 462c ! I Can’t wait to get me paws on the 462c (whenever the dealer comes thru!)- should be able to get 7.2-7.5 hp out of her and with a 20-25” bar and sharp chain it’ll be goodnight Irene !
 
Frank Rizzo said:
Yah , this Saw is at 5.8hp which is .2hp less than a stock 461 or a 462c ! I Can’t wait to get me paws on the 462c (whenever the dealer comes thru!)- should be able to get 7.2-7.5 hp out of her and with a 20-25” bar and sharp chain it’ll be goodnight Irene !
Click to expand...

Nice vid, never seen you post that one before, oh wait that’s the third time you posted it in 3 pages......
 
Frank Rizzo said:
Yah , this Saw is at 5.8hp which is .2hp less than a stock 461 or a 462c ! I Can’t wait to get me paws on the 462c (whenever the dealer comes thru!)- should be able to get 7.2-7.5 hp out of her and with a 20-25” bar and sharp chain it’ll be goodnight Irene !
Click to expand...

It won't work, you clearly state you're a 241,261 and 362 specialist.
 
Frank Rizzo said:
Yah , soon to add 660 to the header and when I get the 462c and dip it into the cauldron of performance it’ll be in the headline too !
Click to expand...
So once you've had your hands on one saw your a specialist on it o_O.
Now if you got paid to work on it you could say you're a professional, but even that doesn't make someone a specialist or an expert.
I'm sure Mr hotsaws101(aka Jack) is proud to be sponsoring such an experienced specialist thru his franchise :laugh:.
 
chipper1 said:
So once you've had your hands on one saw your a specialist on it o_O.
Now if you got paid to work on it you could say you're a professional, but even that doesn't make someone a specialist or an expert.
I'm sure Mr hotsaws101(aka Jack) is proud to be sponsoring such an experienced specialist thru his franchise :laugh:.
Click to expand...
Yah , a good Saw - mechanic should be able to work on ANY Saw right ? Well I can’t very well say I’m a 372xp specialist if I don’t even OWN that particular saw (though I have operated them ) - that wood be dishonest on my part ... look guy I’ve cut / processed More wood than most do in a lifetime ... By using and experimenting on MY equipment I find out what works and what doesn’t ... very simple and straightforward ... as far as Jack aka Hotsaws101, He’s an excellent faller and a very,very good builder . In fact I own a 241c insane-0 and a 461R extreme and am well-pleased with both saws ! Really not interested in your assessment of the situation nor the snarky presumptions you feel you must make for whatever reason ... good day !
 
Frank Rizzo said:
[Never keep up with that 362c in a million years ! You can run a 32” and make one cut ... I’ll strap on an 18” dent puller and plow threw slick fifty and walk around to the other end of slick do him there as well and STIHL have time to smoke slicks fifty's pole and drink juice out of his rocket jammed azz before you finish lolQUOTE]
Click to expand...

Dream on FRANK
 

Latest posts

Back
Top