A look inside the "While You Wait Woods Port" Husqvarna 395XP

[Mastermind]

Have a look at this one fellers.

Edit: I forgot to add that this saw was ported at a while you wait saw shop......I'm just tweaking it a bit.

 

[Mastermind]

After a little tweaking.

 

[Mastermind]

I have no doubt the the saw was a good runner before I tore it down...the before specs....

Compression: 170psi
Squish: .033
Exhaust: 100°
Transfers: 126°
Intake: 79°

After......

Compression: 210psi
Squish: .026
Exhaust: 99°
Transfers: 119°
Intake: 82°

Removed .030 from squish band and about .040 from the base.

 

[Roll Tide]

Wow it might have ran good but that's horrible looking. Did they port it with a grinder or what. But once again great job.

 

[Mastermind]

Wow it might have ran good but that's horrible looking. Did they port it with a grinder or what. But once again great job.

I had to remove a little aluminum..... :hmm3grin2orange:

 

[Roll Tide]

I had to remove a little aluminum..... :hmm3grin2orange:

oh wow, I'm surprised that cylinder cleaned up so nice.

 

[Warped5]

Interesting thread title, Randy.

Do you now have a waiting room, soft music and magazines?



















Nice work as always, BTW .... :hmm3grin2orange:

 

[AUSSIE1]

I have no doubt the the saw was a good runner before I tore it down...the before specs....

Compression: 170psi
Squish: .033
Exhaust: 100°
Transfers: 126°
Intake: 79°

After......

Compression: 210psi
Squish: .026
Exhaust: 99°
Transfers: 119°
Intake: 82°

Removed .030 from squish band and about .040 from the base.

Cleaned up nice Randy.

The before trans would be 116? They ran about 16 in the blowdown out of the box.

 

[wendell]

You didn't meet this saw?!? I'm confused.

 

[Jacob J.]

Interesting thread title, Randy.

Do you now have a waiting room, soft music and magazines?

He has a squad of midgets that massage your knees and elbows while you listen to a CD of "Giraffe Mating, vol. 3."

 

[Warped5]

He has a squad of midgets that massage your knees and elbows while you listen to a CD of "Giraffe Mating, vol. 3."

ROTFLMAO



VERY well played, JJ!


P.S. Somebody please rep JJ, I'm outta ammo.

 

[nmurph]

Interesting thread title, Randy.

Do you now have a waiting room, soft music and magazines?



















Nice work as always, BTW .... :hmm3grin2orange:

Mastermind Saws and Fertility Clinic: The Doctor's Inn.

 

[Warped5]

Mastermind Saws and Fertility Clinic: The Doctor's Inn.

Ooooooooooo ....... Barry White, mood lighting and 'Emotion Lotion!'

 

[Mastermind]

This saw was ported at a shop in Indiana while the owner waited. He thought I could perhaps get a little more.

 

[Warped5]

This saw was ported at a shop in Indiana while the owner waited. He thought I could perhaps get a little more.

Clearly, the saw's owner isn't going to be the only one 'getting a little more!'

:hmm3grin2orange: :hmm3grin2orange: :hmm3grin2orange:




















(Randy, ya stepped right into that one!)

 

[50blues]

Don't forget the dim mood lighting and the massage chair.

 

[Mastermind]

Clearly, the saw's owner isn't going to be the only one 'getting a little more!'

:hmm3grin2orange: :hmm3grin2orange: :hmm3grin2orange:




















(Randy, ya stepped right into that one!)

You want a little too Ted? :msp_wink:

 

[Warped5]

You want a little too Ted? :msp_wink:

Some days there's more than I planned for .... :msp_wink:

 

[blsnelling]

This saw was ported at a shop in Indiana while the owner waited. He thought I could perhaps get a little more.

I believe I remember a few discussions about that shop's mods. I noticed that you went with only 20* of blowdown on this one. I thought you like more than that on the 395. No? How'd it compare?

 

[Mastermind]

I believe I remember a few discussions about that shop's mods. I noticed that you went with only 20* of blowdown on this one. I thought you like more than that on the 395. No? How'd it compare?

I remember that discussion as well Brad......that's why I started this thread.

My "normal" numbers or the 395 are 102°, 122°, 82° or very close. This saw had to have the exhaust raised a bunch to get all the divots and bevel out.