Nik's Poulan Thread

[Welderman85]

I'm going to use a clone later this afternoon on a 3314 let you know that happened tonight

Ok thank you

 

[fossil]

Anyone use the china carbs I'm looking for a zama for my 3314 but all i find is zama clones

The PN for the Zama C1M WC26 carb was superceded by PN 545070601

I see some Zama carbs for sale for that PN. for around $30

 

[RedneckChainsawRepair]

Is he talking about the newer strato carbs? 4218 3314 etc. I think I been paying 15-20 and they work great so far. https://www.ebay.com/itm/CARBURETOR...981812?hash=item3ade422c34:g:DdkAAOSw9itZpVtz

http://chainsawrepair.createaforum.com/poulan/engine-speed-issue/

 

[RedneckChainsawRepair]

Put a new carb and new oiler on this 3314. Old carb shown with issue.

Almost isnt cost effective for a saw I sell for 40-50

 

[Todd Loosli]

This is the Green Ripper cutting 22inches of wood

 

[Jethro 2t sniffer]

This is the Green Ripper cutting 22inches of wood

That right there is an animal

 

[Jethro 2t sniffer]

Listen to that idle mmmm

 

[s sidewall]

You gonna lean it out a tad after you get it broke in? that thang sure does sound and cut good.

 

[s sidewall]

I still just use the old fuji with SD card for video.
Never tried video on the phone yet. Maybe someday.

Bet you can guess what 2 saws got sold.

That PP415 is a ripper for sure.

 

[jerrycmorrow]

Todd, you machinist amaze me. I'm down t0 one arm for a while but I will be watching.

Good seeing ya mm

 

[Welderman85]

Put a new carb and new oiler on this 3314. Old carb shown with issue.

Almost isnt cost effective for a saw I sell for 40-50

View attachment 777900 View attachment 777901

I know what you mean it's easy to put to much money into these saws. I have been trying to make a good beater saw and some how I ended up with 8 different saws all strato plastic 42cc

 

[Modifiedmark]

This is the Green Ripper cutting 22inches of wood

Tipping my hat!

 

[Modifiedmark]

Good seeing ya mm

Thanks Jerry

 

[Welderman85]

On the older 3314 what ratio do I run. I got one all put back together I'm out of fuel so I'm was going to just grab a can of the pre mixed trufuel but don't know 40:1 or 50:1. Thank you

 

[s sidewall]

40:1

Steve Sidwell

 

[s sidewall]

I believe in having some oil in the mix. I used to run 50:1, had no problems but I just like a little extra oil in the mix

Steve Sidwell

 

[3000 FPS]

I believe in having some oil in the mix. I used to run 50:1, had no problems but I just like a little extra oil in the mix

Steve Sidwell

It is a lot better for the bearings.

 

[Welderman85]

Would 40:1 be ok for other saws that saw 50:1 on them like sthil

 

[Todd Loosli]

Say 50:1 is what you meant. Won't hurt anything as far as I know, I have done it all my life, 40:1 has been my favorite other than the big old poulan chainsaws then it's 34:1 for me

 

[Todd Loosli]

I still can't get the 3314 to run right the needles don't do very much when I turn them. High acts like it's starving for fuel when you try wot.