Partner Chainsaw Thread

[av8or3]

The Partner P100. I think it’s an HS172.

 

[av8or3]

You the one needing a carb? Will this one work for needs?

This come off a P55 I parted out instead of putting a recoil spring in. I would bet on it needing a cleaning and rebuild kit. Been in the bin for years now.

Had a nice T-port on it that went to collector.

I dont mess with these anymore.





View attachment 1001055View attachment 1001056View attachment 1001057View attachment 1001058View attachment 1001059
View attachment 1001060

That’ll do! PM inbound.

 

[RedneckChainsawRepair]

That’ll do! PM inbound.

I always open used carbs up anymore for a peek before shipping.

I received one in past that was just all rusty and couldnt save it.
I have since found a few myself I wouldnt sell because of rust even though NLA that come in part saws stashes. I would just open another till found a good one for them.

But this HS172 looks fine opened. No clue inside, been sitting in bin for years now.

 

[edju1958]

I just got an R16 that has no spark.I looked on Feebay for a used module,but could only find one for a 400.I have no idea if it'll work.
If anyone has one I'd be interested in buying it.I'm also missing the front handle with hardware.

 

[Ikeholt]

An aftermarket Husky 55 coil will bolt right on and costs around 15 bucks. Order several, they fit most Partner saws. I probably have an extra handle somewhere. Are you in the lower 48?

 

[edju1958]

An aftermarket Husky 55 coil will bolt right on and costs around 15 bucks. Order several, they fit most Partner saws. I probably have an extra handle somewhere. Are you in the lower 48?

Yeah,I'm in N.Y.I just looked on Feebay for the ignition coil & they're about $10.I might even have one on hand that I was going to use on a Homie saw to replace the blue coil of death.

 

[bob kern]

Anyone desperate for anything seen here. Not a pioneer guy ( yet) so I have no idea what it is lol but would help a fella out if he sees " that one missing part"

 

[bob kern]

Well it looks like I got it in the wrong thread!!
In my defense, I am legally blind lolol.
I'll go try a pioneer thread this time.

 

[Piotr Pakuła]

the color is similar ;-)

 

[Piotr Pakuła]

what mounting the guide does the P100 have? is the model super written on the rating plate?

 

[bryannewton]

Can I get some help on identifying what model and age of thus saw

 

[Piotr Pakuła]

R16 or older / 50 years / provide serial number

 

[bryannewton]

R16 or older / 50 years / provide serial number

I will get the serial number later today where Is it located at

 

[turkeybob]

Picked up a nice 5000+, not done much! one of my favourite 50cc saws, runs well after a bit of TLC!

 

[Piotr Pakuła]

between the silencer and the spur / can also be R15

 

[Piotr Pakuła]

I bring to the state of use R18 / heated handles from the muffler

 

[bryannewton]

between the silencer and the spur / can also be R15

Ok the Serial number is 640211

 

[Piotr Pakuła]

the first association was correct you have R16

 

[bryannewton]

Ok thank you do you know from when it was made

 

[jonsered fan]

Kérhetnék egy kis segítséget, hogy beazonosítsam, hogy milyen modellt és kort látott így?

Hi ! R16. 1967,68,69 !