I saw it on Ebay/Craigslist
- Thread starter trimmmed
- Start date
Help Support Arborist Forum:
GMC Dump Truck
GMC dump truck
--------------------------------------------------------------------------------
Going to look at an '84 3500 gmc dump 4x4. 60,000 on a jasper 350 (never heard of jasper engines?) 30,000 on tranny and new clutch. Has the heavy duty 4 speed with granny low. Will take pics. any recommendations on these trucks?
GMC dump truck
--------------------------------------------------------------------------------
Going to look at an '84 3500 gmc dump 4x4. 60,000 on a jasper 350 (never heard of jasper engines?) 30,000 on tranny and new clutch. Has the heavy duty 4 speed with granny low. Will take pics. any recommendations on these trucks?
rms61moparman
Addicted to ArboristSite
Moss Man
Addicted to ArboristSite
Read my signature, one of the most pratical vehicles you can own. We deliver firewood and plow driveways with it and have no payments and just liability insurance.
So I messed up guys, I was looking at 2 trucks, the one above, and an '86 dump. This is the truck i looked at today. '86 GMC, converted to 6.2 diesel, 4spd w/granny low. This truck was beat! huge hole in floorboard, no front driveshaft, needed new t-case, and a shadetree mechanic hack job to the electric system, and the engine. so no go on this one.
heres the truck i want
http://worcester.craigslist.org/bar/1171111977.html
the one i looked at today
http://worcester.craigslist.org/cto/1164024488.html
valekbrothers
ArboristSite Guru
http://minneapolis.craigslist.org/bar/1177853155.html
alot of little chainsaws (roberts, wi)
--------------------------------------------------------------------------------
Reply to:[email protected] [Errors when replying to ads?]
Date: 2009-05-18, 9:29PM CDT
I have a pile of small homlite, reminton, mcCulloch, and some others that i want to trade. i am listing them as parts saws but i did here a couple run, dont remember witch ones. i am looking to trade for stihl, jonsereds, husqvarna, pioneer, and other similiar saws, for parts.
this is what they are
Homelite xl2, super2, little red,and 150
2 Reminton Mighty mite. one says mongmery wards
2 McCulloch
1Craftsman
And one that i dont know
there is also the 2 plastic cases you see.
thanks
alot of little chainsaws (roberts, wi)
--------------------------------------------------------------------------------
Reply to:[email protected] [Errors when replying to ads?]
Date: 2009-05-18, 9:29PM CDT
I have a pile of small homlite, reminton, mcCulloch, and some others that i want to trade. i am listing them as parts saws but i did here a couple run, dont remember witch ones. i am looking to trade for stihl, jonsereds, husqvarna, pioneer, and other similiar saws, for parts.
this is what they are
Homelite xl2, super2, little red,and 150
2 Reminton Mighty mite. one says mongmery wards
2 McCulloch
1Craftsman
And one that i dont know
there is also the 2 plastic cases you see.
thanks
Moss Man
Addicted to ArboristSite
The 84 looks like a better rig to me.
Texas Traveler
ArboristSite Guru
I would stay away from the diesel & on either one find out what the rear end ratio is.
60mph if you are lucky.
Yeah the 86 is out. The 84's top gear is third, my dad had a similar truck, same trans, its top speed was prob 55? Low gears in diff and trans. We'll see. What did they come with
little possum
Crash and Burn
Good lookin 088 Magnum
http://charlotte.craigslist.org/grd/1176990008.html
Charolette, NC
6 Huskys and 2 Stihls
http://charlotte.craigslist.org/grd/1166647741.html
I emailed him and he said "two 288xp one 039 one 028av two 350 one 340 one 55 rancher some need work some run!!! 800 dollars takes um thats hundred dollars a piece. and will not seperate!!!! ps I WILL NOY GO ANY LOWER THAN 800.00 SOLD AS IS!!!!!!!"
Mooresville, NC
I will gladly take a 288 off of somebodys hands for comission fee
http://charlotte.craigslist.org/grd/1176990008.html
Charolette, NC
6 Huskys and 2 Stihls
http://charlotte.craigslist.org/grd/1166647741.html
I emailed him and he said "two 288xp one 039 one 028av two 350 one 340 one 55 rancher some need work some run!!! 800 dollars takes um thats hundred dollars a piece. and will not seperate!!!! ps I WILL NOY GO ANY LOWER THAN 800.00 SOLD AS IS!!!!!!!"
Mooresville, NC
I will gladly take a 288 off of somebodys hands for comission fee
Texas Traveler
ArboristSite Guru
With a 4 speed manual a good ratio for highway use would be 3.73 for a 6.2. but you better expect a higher ratio in the 4x4s
Moss Man
Addicted to ArboristSite
My 87 has the Low-1-2-3 manual tranny and the gears in the rear end are 4:10, highway speeds of 65 are no problem whatsoever. The third gear I call
4th and it's ratio is 1:1 final drive. Great set-up for work and a low budget.
4th and it's ratio is 1:1 final drive. Great set-up for work and a low budget.
Motodeficient
ArboristSite Guru
quick only 7 minutes left to buy this hotrod saw!
http://cgi.ebay.com/MCCULLOCH-40CC-...ms=66:2|65:1|39:1|240:1318|301:1|293:1|294:50
http://cgi.ebay.com/MCCULLOCH-40CC-...ms=66:2|65:1|39:1|240:1318|301:1|293:1|294:50
This is what im looking at this week in CT. '83 GMC dump, 350 4bbl, 4speed man. talked to the guy today, truck sounds good. 2 wheel drive, but thats ok, I could put a locker in the rear diff, plus less moving parts. The price is right too.
[email protected]
[email protected]
outdoorlivin247
Addicted to ArboristSite
7oaks
DRUGSTORE LOGGER
I do believe that is being offered by a well known AS member. :greenchainsaw:
Bill G
ArboristSite King
outdoorlivin247
Addicted to ArboristSite
Yes I figured that out after I saw the homie 750 for sale...
I do believe the 750 has been sold.
Lee
Lee
Similar threads
