Swap meet...
- Thread starter Four Paws
- Start date
Help Support Arborist Forum:
watsonr
Addicted to ArboristSite
Looking for a Walbro WT-194 to fit an 026. This one does not have the adjustable high screw and I'm going to do a muffmod. Have Homelite SXL/XL12 parts and green. Even have a full wrap for SXL-925.
fredmc
Addicted to ArboristSite
115i coil
still looking for a dolmar 115i coil.
I will have pics later of some parts saws up for grabs.
2-029, 1-290, and two carrot top 350's. Interesting trades and or $$ welcome.
pm w/e-addy to send pics to.
still looking for a dolmar 115i coil.
I will have pics later of some parts saws up for grabs.
2-029, 1-290, and two carrot top 350's. Interesting trades and or $$ welcome.
pm w/e-addy to send pics to.
I'm looking for a carb for a 021, 023, or 025. It must have both L and H needles.
nmurph
ArboristSite.com Sponsor
i need the starter side cover for a 385. it need not have the spring and spool.
sjames
ArboristSite Lurker
need brake assembly for 268xp
I am in need of a brake assembly or just the brake parts inside the cover for a older 268xp with the aluminum brake handle/lever. The saw is an 1988
I am in need of a brake assembly or just the brake parts inside the cover for a older 268xp with the aluminum brake handle/lever. The saw is an 1988
logging22
Cuttin to live, livin to cut
Might have this. Give me time to look tomorrow.
Harzack223
ArboristSite Operative
Looking for an 034 engine cover. Have some stihl parts and cash.
logging22
Cuttin to live, livin to cut
Sorry Brad, no luck.
mrinds
ArboristSite Member
Sachs Dolmar 120 si
Could really use a flywheel and a pull starter & cover for a saw I picked up yesterday. The Sachs Dolmar 120si. Piston & Cylinder are so clean, looks almost new. Compression is 140 and I have decent spark. The rest is still to be determined. But I'll start out trying to get the body back together. Thx .
Best Regards
Mike
Could really use a flywheel and a pull starter & cover for a saw I picked up yesterday. The Sachs Dolmar 120si. Piston & Cylinder are so clean, looks almost new. Compression is 140 and I have decent spark. The rest is still to be determined. But I'll start out trying to get the body back together. Thx .
Best Regards
Mike
fredmc
Addicted to ArboristSite
I'm looking for the plastic divider between the carb/cylinder and a front/bottom rubber buffer that connects the tank to the front AV-for a 262xp husky.
got green and trades just ask
BTW are these parts the same on a 254/257???
got green and trades just ask
BTW are these parts the same on a 254/257???
Last edited:
Disston DO-100/101
Anybody have a running one, or parts, or know where to find parts? Mine has a Stromberg carb on it, parts NLA. If you have a runner, whats on yours? Cash or trades for carb parts, make an offer on the whole saw with the bar and straddle scratcher chain if you want, may or may not be an option.
Anybody have a running one, or parts, or know where to find parts? Mine has a Stromberg carb on it, parts NLA. If you have a runner, whats on yours? Cash or trades for carb parts, make an offer on the whole saw with the bar and straddle scratcher chain if you want, may or may not be an option.
Bars up for grabs
Got some extra bars, chains etc to move out of here.
There are three Homelite bars and chains pictured, left is a 18".325 bar and chain from a Homelite 27AV. Will also fit small Husky mount. Center is a 16" bar and chain in .325 (I think) from Homelite 245. Right is a 14" 3/8'slp from a Homelite XL or Super2. I also have a 16" bar for them as well.
This Tilton super bar fits the little Ebab saws like the Frontiers, Jred 361, Skil 1616 etc and it appears to be a 16" 3/8s low pro.
This Skil bar has never been used, but I have no idea what saw its for.
Also have some 14" bars for the mini macs, one 1/4 pitch with chain and one 3/8s lp.
Will trade for whatever but basically just need them out of here.
Got some extra bars, chains etc to move out of here.
There are three Homelite bars and chains pictured, left is a 18".325 bar and chain from a Homelite 27AV. Will also fit small Husky mount. Center is a 16" bar and chain in .325 (I think) from Homelite 245. Right is a 14" 3/8'slp from a Homelite XL or Super2. I also have a 16" bar for them as well.
This Tilton super bar fits the little Ebab saws like the Frontiers, Jred 361, Skil 1616 etc and it appears to be a 16" 3/8s low pro.
This Skil bar has never been used, but I have no idea what saw its for.
Also have some 14" bars for the mini macs, one 1/4 pitch with chain and one 3/8s lp.
Will trade for whatever but basically just need them out of here.
Mark-
I can use the 16" Tilton bar and the 1/4" pitch bar and chain for one of my projects. Let me know what you need.
I can use the 16" Tilton bar and the 1/4" pitch bar and chain for one of my projects. Let me know what you need.
wigglesworth
Booned
I might have some 1/4 pitch loops on some mini macs, and I think I might have one other as well. If I do, Ill stick them in that box with the other saw.
wigglesworth
Booned
Scratch that thought....they have 3/8 LP on them...sorry.
Saw Dr.
Junk Collector
This Skil bar has never been used, but I have no idea what saw its for.
That cutout looks like a very old MAC mount to me.
Yeah me too but did mac ever badge a saw for Skil?
The oiler hole seems to be on the wrong side dont it?
