Swap meet...
- Thread starter Four Paws
- Start date
Help Support Arborist Forum:
ChainsawmanXX
Addicted to ArboristSite
ARRGGGG!! You made me work!
Its clean now.
Watch out there Mr King :msp_angry:
Bump!!! Anyone have ANY clue where to source these parts at??? (Stihlership will be the LAST resort!)
okay guys, i am going to see what you guys got going here.... I need:
2 sets of Stihl 056 bearings.... Would love NOS!
same with seals!
a Few (5 ish) Stihl Name plates, as you have riveted on the side of a recoil (NOS is great! and Id like if they said "made in west Germany"!
Some metric rivets for the Above item would help also!
And also looking for used P/C kits for the 056 super, and 056 magnum 2 varieties! I need one of each :/
okay guys, i am going to see what you guys got going here.... I need:
2 sets of Stihl 056 bearings.... Would love NOS!
same with seals!
a Few (5 ish) Stihl Name plates, as you have riveted on the side of a recoil (NOS is great! and Id like if they said "made in west Germany"!
Some metric rivets for the Above item would help also!
And also looking for used P/C kits for the 056 super, and 056 magnum 2 varieties! I need one of each :/
o8f150
Tree Freak
i don't have the saw yet but does anyone have the recoil assembly for an olympic 355af ??? if i can find the parts i am going to buy the saw for 10.00,, have useless green paper and some parts for trade
o8f150
Tree Freak
from what i hear thats what his wife says too :msp_biggrin::msp_biggrin:
ChainsawmanXX
Addicted to ArboristSite
I found out the hard way yours likes the whips an chains!! :0
How else can his wife keep him in line? :hmm3grin2orange:
Scooterbum
Addicted to ArboristSite
Have what appears to be the Monkey Wards 2.1 cu. in. version of the McCULLOCH MacCat-WildCat type saw.
I'm looking for a clutch and sprocket assembly for it. Have green stuff to trade.
I'm looking for a clutch and sprocket assembly for it. Have green stuff to trade.
thomas1
sodium pentothal
- Joined
- May 2, 2010
- Messages
- 3,651
- Reaction score
- 1,092
Scoot, can you poat a pic? I've got a few carcasses, here.
Would seals/bearings from a plain old, as in not "Magnum", 045/056 work? I might have them, I have a bunch of NOS stuff, but I don't know the how the bearing and seal part numbers work, so I haven't gotten around to sorting them out. If you can provide me with part numbers, I'll see if I have what you're looking for.
Bryan
Scooterbum
Addicted to ArboristSite
Have 056 magII and super cylinders, no pistons though.
Scooterbum
Addicted to ArboristSite
Sent via text to your phone. It's a TMY240 model. Also need the little plastic plate that covers the carb.
The pistons are the hard part to come up with for the Magnums/Magnum IIs.
Scooterbum
Addicted to ArboristSite
No aftermarket ? I'll have to do some digging then, I'm sure I have some used ones here.
There are some Chinese pistons being made but the reviews so far are not good. Even good used OEM would be better, and if they're worn past
specs, then a guy could have Millennium Technologies coat the piston to bring it back.
parrisw
Tree Freak
If there was enough of you guys interested, you could doo what Lee did for the 166's and have a bunch made.
Metals406
Granfodder Runningsaw
And the 056 pistons work well in 066's! :msp_biggrin:
Mastermind
Work Saw Specialist
If this ends up going somewhere I would be in for a few....
I've built three 066s for saw millers using the 056 Super piston, it does make a good running machine.
It's not a high-winder, but they make good torque.
