Swap meet...

[psuiewalsh]

psuiewalsh : If you dont mind, ill take it. I have a bar and chain i believe that is yours that i found under my truck seat the other day?

Howd that 045 turn out? It looked to have great potential!

Please pm me your info again. The 045 is still on the shelf. It ran good for a bit after I rebuilt it with a new cylinder but has ignition issues. I put in a chip per another thread and it will run until it gets hot. That is why I do not know if this coil is good or bad. I have a bosch 041 coil in there now. I know that there are complete units from Germany but they are over $100 and I just am not there yet.

 

[mdavlee]

I need rivets for the old 3 rivet oregon tips. I have some parts and some worthless green paper.

 

[Eccentric]

I need rivets for the old 3 rivet oregon tips. I have some parts and some worthless green paper.

How many do you need Mike?

 

[mdavlee]

How many do you need Mike?

3:beer:

 

[Eccentric]

3:beer:

Lemme go through my 'bar rivet jar'. Can probably dig out three of those for you.

 

[Arrowhead]

I need rivets for the old 3 rivet oregon tips. I have some parts and some worthless green paper.

A few months ago I was looking for them. They are 3/16" diameter. I check with all the sponsor saw shops, Gregg couldn't even order them. The Stihl rivets are very close and will work fine. Somebody here gave me this link... you need to scroll down a little to the "countersunk head solid rivets" A bag of 100 is less than $10.
McMaster-Carr

EDIT.... I see now you only need 3, if Aaron can't come up with them, I have em. Just let me know.

 

[mdavlee]

Lemme go through my 'bar rivet jar'. Can probably dig out three of those for you.

Thanks Aaron.

 

[mdavlee]

A few months ago I was looking for them. They are 3/16" diameter. I check with all the sponsor saw shops, Gregg couldn't even order them. The Stihl rivets are very close and will work fine. Somebody here gave me this link... you need to scroll down a little to the "countersunk head solid rivets" A bag of 100 is less than $10.
McMaster-Carr

That's good info there Ed:thumbup:

 

[Arrowhead]

That's good info there Ed:thumbup:

In case you didn't see my edit... I can send you 3 if Aaron can't find any.

 

[mdavlee]

I seen it now. If he can't I'll take them off your hands so I can have another 32" bar ready to go.

 

[Warped5]

3:beer:

Lemme go through my 'bar rivet jar'. Can probably dig out three of those for you.

Aaron, I thinx you missed something ... Mike's reply was that he needed three beers. :jester:

 

[Arrowhead]

No problem, just let me know.

Speaking of rivets, I have quite a few of the Oregon single rivet types if anybody needs some.

 

[Mastermind]

I made a boo boo......and now I need an 076 jug and piston. :msp_unsure:

 

[Jacob J.]

I made a boo boo......and now I need an 076 jug and piston. :msp_unsure:

I wish I could help you...I have all the 051 jugs a guy could ever want.

 

[Eccentric]

Looks like I'm in need of a good 288XP cylinder. I have various parts from old McCullochs, Homelites, and Poulans to trade. Also have a Husqvarna 350 that may go on the block....

 

[jbird77]

carb

Iam still in need of a WJ 39 carb even just a good body. From a 064/066 . Or husky . Got lots of saw parts let me know what u need .

 

[booger1286]

Looks like I'm in need of a good 288XP cylinder. I have various parts from old McCullochs, Homelites, and Poulans to trade. Also have a Husqvarna 350 that may go on the block....

I may have a couple if your interested. Let me know what you have for trade.

 

[Scooterbum]

Iam still in need of a WJ 39 carb even just a good body. From a 064/066 . Or husky . Got lots of saw parts let me know what u need .

I could use a cracked fuel line and a clogged up filter.

 

[Arrowhead]

Anybody have a junk intake boot for a 372 layin around.
I just need for a test fit...

 

[Jacob J.]

Anybody have a junk intake boot for a 372 layin around.
I just need for a test fit...

I have several...I can get one headed your way tomorrow.