Swap meet...

[BigDaddyR]

Would one out of a plain old 45 work? As in the 40/45/49 series? I'm not too familiar with these saws, but do have a bunch of them.

Bryan

Yep a plain 45 would work. Don't know what's so special about the special as it is not mentioned in the IPL. Special sticker maybe. LOL. Here's a pic of the #'s on it. Thanks and let me know.

View attachment 308896
View attachment 308897




Sent on the fly.

 

[MS460WOODCHUCK]

That's good info to know Kevin. Unfortunately, that coil won't work on the S E-Z. John needs one of the infamous 'blue coil' electronic ignitions for a Homelite Super E-Z. If somebody finds a match for that bugger (from some other, more common source) then there will be some happy Homelite guys. Swapping to a points ignition isn't easy with those saws, as the electronic ign saws have a different crank with no points cam cut on it. A fellow could use a points coil with an Atom/Nova type trigger though.

Thanks for the info..but now its not looking to good on the finding one issue:help:

 

[Mastermind]

I'm looking for Stihl TS350 powerheads. They must have electronic ignition. Condition isn't too important. I'm needing the ignition module of one pretty badly right now. These powerheads are used on anchor driving machines that a cable company here uses......they are getting older so parts units are needed.....

Thanks!!!!

 

[hemiyota]

Poulan 8500

I need a throttle wire (linkage) for an 8500 series saw. Anyone have an extra one?????

 

[PogoInTheWoods]

I'm looking for Stihl TS350 powerheads. They must have electronic ignition. Condition isn't too important. I'm needing the ignition module of one pretty badly right now. These powerheads are used on anchor driving machines that a cable company here uses......they are getting older so parts units are needed.....

Thanks!!!!

Should be the same as an 08S if ya have any electronic versions laying around that aren't needing a port job.:msp_tongue:

 

[Mastermind]

Should be the same as an 08S if ya have any electronic versions laying around that aren't needing a port job.:msp_tongue:

Yes sir.......that's true.

 

[RenaisSAWnceMan]

Looking for a good piston/cylinder/ring for a Husqvarna 45 Special. Husky part# 503 44 08-02. Other models that will fit it and are same part# are Jred 2045, Husqvarna 245r and 245 RX. Have paper and some other minor stuff to trade. Let me know.

Thanks

I have a clean-enough-looking 45.... The pull-cord is frozen...and, haven't checked yet to see it the 'freeze' goes any deeper....:msp_ohmy:

I'll try to check it out, and get back to you. Please feel to keep after me.... If it is alright, you are welcome to it...the whole thing.

 

[cutforfun]

Looking for a sachs dolmar 114 clutch cover and chain brake, not sure what other models will fit. Lots of stuff to trade or cash

 

[lwn9186]

Looking for an GX31 or GX35 Honda engine to repair my WX10 pump.

 

[cowroy]

Looking for a sachs dolmar 114 clutch cover and chain brake, not sure what other models will fit. Lots of stuff to trade or cash

cutforfun has exceeded their stored private messages quota and cannot accept further messages until they clear some space.

 

[LowVolt]

BRASS HAMMER, that FUNKY HAMMER
BRASS HAMMER - JUNKIE
That FUNKY HAMMER!!!!

:hammer:

 

[psuiewalsh]

Looking for a sachs dolmar 114 clutch cover and chain brake, not sure what other models will fit. Lots of stuff to trade or cash

looks like models 112 114 117 120 120S. I saw one the other day but I think the band was broke/missing.

 

[cutforfun]

cutforfun has exceeded their stored private messages quota and cannot accept further messages until they clear some space.

Made some more room, thanks

 

[cutforfun]

looks like models 112 114 117 120 120S. I saw one the other day but I think the band was broke/missing.

Let me know, I could find a band

 

[BigDaddyR]

I have a clean-enough-looking 45.... The pull-cord is frozen...and, haven't checked yet to see it the 'freeze' goes any deeper....:msp_ohmy:

I'll try to check it out, and get back to you. Please feel to keep after me.... If it is alright, you are welcome to it...the whole thing.

That would be great. Let me know and if I don't hear or I round one up I'll check back in with you. Know what it's like to be busy.

 

[Brushwacker]

6 tooth 3/8 picco sprockets needed for Stihl ms180,170 etc. could use 1 for an 021 to

I am looking for new or like new condition 6t picco sprockets that fit the 017 to the ms 180 and could take 1 for an 021, needs to be 6 tooth also. Wouldn't mind getting an Stihl laminated 16" 3/8 bar in very good condition also.
To trade: Sprockets- new stuff that’s been sittin around, came from a Husky dealer that quit, some has minor tarnish and or very minor rust , nice new bearing included unless specified not.
1) Spur-style: P/N 5030887-02 SWEDEN .325 pitch 7 t. Husky 50,Special,51,55 Rancher + EPA
1) Spur-style: P/N6402000-84-Oregon P/N 28001 6 t. 3/8 lo pro fits small Husky, 33,34,35,37,etc.Jonsered 36 etc. Pioneer P12, Partners, Frontier, Skil
1) Oregon Power Mate rim Systems 7t .325 P/N 6402000-97, Oregon P/N 29105 P fit Husqvarna 42, 133, 234, 238, 242 etc.
1) 5034539-02 Not sure on fit but it looks like the same as P/N 5030887-02 Husky 50,Special,51,55 Rancher + EPA, no guarantee on fit so know what P/N you need. 3/8 7 t .rim
Also have sprocket hubs in good condition for 026-260 saws and 1 or 2 for 361, 044,ms440. Also have chains to trade, new and used, just tell me what ya need and I'll see if I have it.

 

[psuiewalsh]

Let me know, I could find a band

PM sent

 

[psuiewalsh]

Looking for a good carb for a stihl 064.

I have the walboro WJ6? but cannot get the low to work and the lever has to be way high for it to even run. I do not have an ultrasonic bath yet to try and clean it out. I have already pulled and re installed the Welch plug so don't think that was the issue it must be deeper. I have one I borrowed off my other saw and it runs fine. Old carb has same issues on second saw.

I have some stuff and funds to trade. If there is not a known good one to trade has anyone had success with the china made ones that fit the 066/660?

 

[sld961]

Looking for a good carb for a stihl 064.

I have the walboro WJ6? but cannot get the low to work and the lever has to be way high for it to even run. I do not have an ultrasonic bath yet to try and clean it out. I have already pulled and re installed the Welch plug so don't think that was the issue it must be deeper. I have one I borrowed off my other saw and it runs fine. Old carb has same issues on second saw.

I have some stuff and funds to trade. If there is not a known good one to trade has anyone had success with the china made ones that fit the 066/660?

PM sent

 

[nmurph]

Looking for a good carb for a stihl 064.

I have the walboro WJ6? but cannot get the low to work and the lever has to be way high for it to even run. I do not have an ultrasonic bath yet to try and clean it out. I have already pulled and re installed the Welch plug so don't think that was the issue it must be deeper. I have one I borrowed off my other saw and it runs fine. Old carb has same issues on second saw.

I have some stuff and funds to trade. If there is not a known good one to trade has anyone had success with the china made ones that fit the 066/660?

Keith, send it to me if you want. I will run it through the USC for a couple of hours. No charge...just pay the postage.