Oklahoma,AR,MO,KS,TX GTG (Next GTG 08/27/2016 ) Fort Scott, KS

[sawnami]

OK Matt thanks.I need to get that ordered. HI Coby was that Mono made ib Baxter Springs?Been running weedeaters all week,I hope I am caught up now.

Mono was made in Springfield, MO

Root was made in Baxter Springs, KS



Sent from my SM-N910V

 

[cobey]

OK Matt thanks.I need to get that ordered. HI Coby was that Mono made ib Baxter Springs?Been running weedeaters all week,I hope I am caught up now.

I have a "root" made in Baxter....... I saw a root in mint condition a while back

 

[cobey]

Cut a full load of hedge logs again today..
562 still has not blown up..
Go figure..
Lol.

You should test saws for husky....but for $$$

 

[cobey]

Mono was made in Springfield, MO

Root was made in Baxter Springs, KS



Sent from my SM-N910V

My mono has a little diamond shaped sticker with 5 hp on it

 

[Hedgerow]

Good morning all.
Sure is nice this time of day..

 

[bigtuna]

Good morning everone, ya Matt best part of the day imo.

 

[SteveSS]

Morning Matt, Tuna, and everyone else.

 

[Hedgerow]

 

[Hedgerow]

I'll deliver that load today and cut it to length on the truck.

 

[67L36Driver]

Mono was made in Springfield, MO

Root was made in Baxter Springs, KS



Sent from my SM-N910V

The green one looks yummy.[emoji12]

Morning midlanders!

Cleanup on aisle 034 this morning. Then measure the bore to see if we buy just piston w/rings or whole top end.

Bar needs dressed bad!

 

[67L36Driver]

Wear those safety glasses!

Got sprayed in the face with fuel when I disconnected the line on the 034. Emptied the tank but there was enuff fuel in it and vapor pressure in the tank.

 

[67L36Driver]

46mm piston kit is 22 bux and the 48mm top end kit is 50 bux.
What to do? This is not a keeper.

Cylinder is in excellent shape.

 

[jetmd]

Lunch break time.

Carl if it was me I would keep the stock jug and do the $22 piston kit. JMHO

You guys have a good day, later.....

 

[workshop]

Lunch break time.

Carl if it was me I would keep the stock jug and do the $22 piston kit. JMHO

You guys have a good day, later.....

I agree, no point in doing the goody stuff to it. The buyer will likely mess it up anyway.

 

[sawnami]

Cleaned up the 695.

Sent from my SM-N910V

 

[67L36Driver]

Cleaned up the 695.

Sent from my SM-N910V

Stylish looking devil![emoji41]

 

[67L36Driver]

A lot of fellows might just put in new rings but this one has over .010" skirt clearence. Yikes!

 

[cobey]

Cleaned up the 695.

Sent from my SM-N910V

How. Does it run?

 

[sawnami]

How. Does it run?

Seems to run pretty good. Going to see what a little change in the muffler may have to offer.

 

[cobey]

I played with muffler mods on the "workshop" 024 as
Close to 100 percent the exhaust pot you could get to about 90
It ran strong ...... at its biggest it had an erratic idle ....
Offsetting the holes it would idle and run hard.....
It's about 90 + percent with offset ports and it responds like a ported saw!
I had to weld the muffler some ..... I Will take a pic next time it's apart
I tested it in 14 inches of hard dead elm.