Revised Mini-Mill

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Very good BobL...,er Jerry. Sure you haven't spent a little time in the Australian bush wrestling crocs and dingos trying to get to that hard to reach perfect dead tree to auto-mill?
 
Post 9

Finished the chip/dust deflector today. It was raining out all day so I just turned the radio on and played in the shop.

jerry-

Here some pictures of how I made the deflector and materials used.

Closeup of chip/dust deflrector.
I made it from 1/2"x1/2" angle iron
1/2" x 1/2" square tubing
A piece of 1/2" diameter tubing
1ea 1-1/2"x1-1/2" x 1/8"thick metal
2ea 1/4-20 bolts and nut
1ea 5/16-16 bolt
2 ea 1/2" OD 1/4" ID bushings 3/4" long

attachment.php


Deflector film curving away from saw.

attachment.php


Deflector Film curving towards saw.

attachment.php


Closeup of how film is clamped to bracket.

attachment.php


Closeup of clamp open. You can see how I welded the bushings to the angle so it clamps the film by just tightening the two ny-lock nuts.

attachment.php
 
Post 10

I will try using the film facing both directions to see which way works the best.

The Polycarbon film is pinched by the two bolts and is very secure.

attachment.php


Stopped raining long enought for me to remove the saw and take a picture of the frame/throttle assembly and the dust/chip deflector.

attachment.php


No bells or whistles BobL, But....

I have a warning horn for those people not paying attention, an AM/FM radio for break time and a GPS so I won't get lost going to the mill site. It's endless on what I can attach.

attachment.php


I just couldn't find any bells/whistles....

Cool Huuuu... Had to have some fun!

attachment.php


Only thing let to do now is paint the dust/chip deflector piece and give it a try. We are forecast for heavy rain all the way till next Thursday so testing will have to wait.

jerry-
 
GPS - Dang - now why didn't I think of that! I guess it's one way to measure linear feet cut? :D

Is the deflector clamp touching the bottom of the saw? If so the saw vibe will make it rattle against the clamp and it could mangle the base of the saw.
 
Thanks, I think it took me longer to make the throttle piece than the actual mill/parts. I do hope the pictures help anyone considering building a mini-type-mill. I know seeing pictures on this list helped me with ideas to build my big Alaskan style mill.

jerry-

Jerry-
:yourock:

I am always impressed by your ideas and how you put them together. Thanks for sharing with us. Great pics too!
Lou
 
WHOA! awesome job on the mill- really nice looking fab skills. I'm going to try to get a mini together over the next few months but i'm not even going to kid myself by hoping it looks as clean as yours.

One thing i do want to think about is having the saw mount pivot, or maybe clamp the bar instead of bolting to it as a means of regulating depth of cut.

but this is giving me something to aim for, thanks.

Okay enough about the mills, lets see some more pics of that sweet GT350!!!:bowdown: Is that original????
 
GPS - Dang - now why didn't I think of that! I guess it's one way to measure linear feet cut? :D

Hey, maybe I should put a laser on it to align my cuts... :dizzy:

Is the deflector clamp touching the bottom of the saw? If so the saw vibe will make it rattle against the clamp and it could mangle the base of the saw.


Hi Bob,

No, the clamp does not touch the bottom of the saw. It's about 3/4" away from the bottom of the saw. I thought about that to when I was cutting the tube to length and figured since the bottom of the saw/handle is part of the gas tank, it had better not touch.

jerry-
 
WHOA! awesome job on the mill- really nice looking fab skills. I'm going to try to get a mini together over the next few months but i'm not even going to kid myself by hoping it looks as clean as yours.

Thanks

One thing i do want to think about is having the saw mount pivot, or maybe clamp the bar instead of bolting to it as a means of regulating depth of cut.

I couldn't keep my bar from pivoting on my first mini-mill so that is why I built this mill with it bolting through the bar to the mounting block. If you do decide to use the pinch style for mounting your bar, be sure to space your bolts out from the chain. Too close and when the chain starts to get loose it will start hitting the all-thread rods or bolts if you use them. I speaking from experience.


Okay enough about the mills, lets see some more pics of that sweet GT350!!!:bowdown: Is that original????

Yes the 66 GT-350H is real. I bought it in 1971 wrecked for $700 from Bill Maier who was going to part the car out. I ended up building SCCA/Trans Am race cars for Bill for fifteen years. It was the Red/Gold Hertz rental at the Oakland, CA Airport. #0829 His son Mike Maier just won the 2010 SCCA Solo 2 championship this year in another car I worked on. The car is Frank Stagnaro's clone 66 GT-350.

I'll see if I have any scanned pictures of my car I can post.

jerry-
 
Is the deflector clamp touching the bottom of the saw?[quote

Bob, this pictures shows how far away the bracket is from the saw bottom. I should have noted that it does not touch the saw at all. Good call.

Looks good, it will be interesting to see how much if any sawdust gets through that gap.
 
Looks good, it will be interesting to see how much if any sawdust gets through that gap.

Bob, was thinking about your comment. I think I could use a piece of light foam of some sort and attach to the top of the bar so it just touches the bottom of the saw if I find sawdust is spouting over the top of the bracket. I'll know when I mill.

jerry-
 
Bob, was thinking about your comment. I think I could use a piece of light foam of some sort and attach to the top of the bar so it just touches the bottom of the saw if I find sawdust is spouting over the top of the bracket. I'll know when I mill.

Looking at your guard has I've started thinking about a chip deflector for my 440 when I use it in my minimill and the am thinking it might be more effective attaching it to the saw itself.

This would be relatively easily done by replacing the screws at the ends of the wrap handle with longer screws and adding short standoffs that would permit a custom made deflector bracket to be mounted onto saw. The guard would then be firm up against and not abrade the saw body.

The bracket would look something like this;
attachment.php


Here's another view looking direct at the underneath of a saw.
attachment.php


On the first version of the BIL mill I made a nose guard from polycarbonate that looked like this.
attachment.php

It vibrated itself to bits after only about 10 logs so I remade it with more attachment points and ally support brackets but the PC still cracked and so I got rid of it.

So instead of a flexible deflector which might also rattle up against anything it touches and eventually vibe itself to bits anyway I'm thinking a solid cowl from ally or plastic that deflects the chips sideways would be better. Also it would reduced the amount of sawdust that falls onto the log and has to be swept off so the guide board can lay flat.
 
Looking at your guard has I've started thinking about a chip deflector for my 440 when I use it in my minimill and the am thinking it might be more effective attaching it to the saw itself.

This would be relatively easily done by replacing the screws at the ends of the wrap handle with longer screws and adding short standoffs that would permit a custom made deflector bracket to be mounted onto saw. The guard would then be firm up against and not abrade the saw body.

The bracket would look something like this;
attachment.php
Bob, sounds good, but I would think if you were going to make it wrap around the saw, it had better be one continuous piece of aluminum tubing that you like to use. I would think you are going to get more vibrations mounted directly to the saw vs on the frame.

I wanted my setup to take as little time to setup and take apart. I have two thumb screws on the throttle mechanism and the two bolts holding the saw to the frame. I don't have dedicated saw for my mini-mill and if you do then time switching out is not an issue.


On the first version of the BIL mill I made a nose guard from polycarbonate that looked like this.
attachment.php

It vibrated itself to bits after only about 10 logs so I remade it with more attachment points and ally support brackets but the PC still cracked and so I got rid of it.

I made my nose guard from 3031 aluminum and it hasn't cracked yet. Some plastics just don't like a lot of vibration.



So instead of a flexible deflector which might also rattle up against anything it touches and eventually vibe itself to bits anyway I'm thinking a solid cowl from ally or plastic that deflects the chips sideways would be better. Also it would reduced the amount of sawdust that falls onto the log and has to be swept off so the guide board can lay flat.

My vote is for aluminum, you can also isolate the mounting points with rubber washes and use a ny-lock nut.

If you use a solid deflector and my system has the flexible polycarbon we could be testers for anyone else wanting to make a dust deflector for any mill.

I won't be doing any milling to soon with all the rain we will be getting forecast through next Thursday.

jerry-
 
Bob, sounds good, but I would think if you were going to make it wrap around the saw, it had better be one continuous piece of aluminum tubing that you like to use. I would think you are going to get more vibrations mounted directly to the saw vs on the frame.

True, but your guard is on the end of a long arm so the initial flex is much greater to begin with and small vibe on long flexible arms have a way of magnifiying the vibe on the end of the arm. It's amazing how vibe is transmitted thru what seems like a fixed point in a system.

I wanted my setup to take as little time to setup and take apart. I have two thumb screws on the throttle mechanism and the two bolts holding the saw to the frame. I don't have dedicated saw for my mini-mill and if you do then time switching out is not an issue.
Yep I agree - if it's your only saw then a cowling bolted direct on the saw wmayill take longer to take apart - but it maybe no slower than removing your remote trigger - anyway I will have a fiddle.

I made my nose guard from 3031 aluminum and it hasn't cracked yet. Some plastics just don't like a lot of vibration.
My nose guard is only supported at one point which is when stuff vibrates itself more easily to bits

My vote is for aluminum, you can also isolate the mounting points with rubber washes and use a ny-lock nut.
Good idea

If you use a solid deflector and my system has the flexible polycarbon we could be testers for anyone else wanting to make a dust deflector for any mill.
Another Good idea

I won't be doing any milling to soon with all the rain we will be getting forecast through next Thursday.
Dryest year on record here and it's been raining all day (mid summer) but we have over 100F forecast for Xmas Day.
 
Last edited:
Post 11

I've been fighting off the Christmas cold and decided I needed to get out of the house and into the shop.

So, I made a quarter saw attachment for the mini-mill. I had some 3/16" aluminum that cut down to make the piece with. It is adjustable to what ever with boards I want to mill. I need to make some fence boards and this could be just the ticket.

jerry-

Quarter saw attachment mounted on mini-mill.

attachment.php


Here is a top view with the quarter saw attachment adjusted to a 1" board thickness.

attachment.php


Angle view of 1/2" adjustment bolts. I will cut thickness blocks for milling different thicknesses.

attachment.php


View with a bar mounted. I have a friend who has a custom aluminum fabrication business and he let's me dumpster dive his scrap. It's heaven!

attachment.php
 
Great work and thanks for the great step by step. I have only used the Alaskan style so far but I'm looking into building a mini soon to compliment it. I have a couple questions. What is the longest bar you can get away with?

This mill can be used with what ever saw/bar combination you have. I'm thinking of getting a 24" bar for this saw which is about max I would think.

Second, is there any thoughts about setting it up so it could cut at 45 deg instead of 90 deg to make it cut easier? Many of the logs I mill are located where it is hard/imposible to roll them and some are to big for my current 36" cut so the mini would only be used to narrow the sides for me.

With this setup you could operate it at a 45* angle. You would just need to be sure to keep the mill on the board and not let it lift off. I would say, cut the first cap cut at a 45*, then the rest of your cuts will follow that angle. Once you have milled enough boards from the log, it could be rotated to 90*. I'll try that on the next log I mill and post how it worked. I'll be getting more logs on Monday, then it's more rain the rest of the week. :-(

jerry-
 
Beautiful Job!

Jerry,

You have done an excellent fab job on your mini mill. :bowdown:

I too am considering building versus buying both a mini and a full-size 36" Alaskan type mill, so I REALLY appreciate you taking the time to share detailed pictures and explanations of your very nice buildup.

I noticed that your last post was a bit ago so I'm wondering if you've had time (and weather that has cooperated) to operate your mill. Let's see how it's working out for you!

I was talking to Eric at Granberg, about mills and specifically with reference to minis, about bar length. I was thinking about a 28" bar on an 80cc Mac w/404 ripping chain (dedicated to the mill) and he said that woud be fine, and for smaller logs I could adjust the saw upwards for clearance at the bottom of the log. I'm assuming that the Granberg Mini uses the bar-pinch mounting method so it makes it real easy to adjust saw height, although with the method you've selected additional bar holes takes care of that quite easily as well. In fact I think I like direct mounting through the bar as you've done better, as it is a more secure and safer way of doing it IMHO.

I'm really curious as to the saw wanting to lift the mill off the log. That's my only hesitation in using the top of the bar to cut with. Does it exhibit any tendency at all to want to lift?:msp_confused:

Thanks again for sharing. This is great stuff. Keep it coming.:hmm3grin2orange:

BTW, did you post similar info on your full-size mill build? If so where can I find it?

Whoops, just found your other post which shows you in action. Here---> http://www.arboristsite.com/showthread.php?t=164433
 
Last edited:
Jerry,

You have done an excellent fab job on your mini mill. :bowdown:

Thank You

I noticed that your last post was a bit ago so I'm wondering if you've had time (and weather that has cooperated) to operate your mill. Let's see how it's working out for you!

ProGT,

I have actually used the mill a few times since I finished building it and have built a second mini-mill for my neighbor. I have found the mini-mill easy to setup/operate. A few basic things to do before milling and it's all fun after that. I have found that using the rail board makes the cuts very accurate. Here is a picture of a cant I cut this past weekend and you can see it is square and is square on all four corners.

attachment.php


I was talking to Eric at Granberg, about mills and specifically with reference to minis, about bar length. I was thinking about a 28" bar on an 80cc Mac w/404 ripping chain (dedicated to the mill) and he said that woud be fine, and for smaller logs I could adjust the saw upwards for clearance at the bottom of the log. I'm assuming that the Granberg Mini uses the bar-pinch mounting method so it makes it real easy to adjust saw height, although with the method you've selected additional bar holes takes care of that quite easily as well. In fact I think I like direct mounting through the bar as you've done better, as it is a more secure and safer way of doing it IMHO.

The very first mini-mill I built was a close clone to the Granberg version how it clamped the bar. Yes it is easy to adjust the depth of the cut by rotating the bar forwards or backwards. I just didn't like the idea of the blade possibly moving while milling that is why I decided to drill the mounting holes on the bar. Just my preference I suppose.

I'm really curious as to the saw wanting to lift the mill off the log. That's my only hesitation in using the top of the bar to cut with. Does it exhibit any tendency at all to want to lift?:msp_confused:

I have milled a verity wood from pine to oak and really haven't experienced a problem with the mill wanting to lift while milling. I'm sure the weight of the mill/saw combination would be a factor, but I'm only using a 65cc saw. If you plan to use a 80cc+ saw it won't even be a issue. If you were experiencing a problem with a particular piece of wood you could always pull the mill through the log vs pushing. Pulling the mill backwards would be pulling the mill down onto the wood. In fact, I will try it the next time I mill to see if I see a big difference.

Thanks again for sharing. This is great stuff. Keep it coming.:hmm3grin2orange:
Everyone here comes up with some great ideas and I have used many of them on my mills and other pieces like log lifters, etc.

BTW, did you post similar info on your full-size mill build? If so where can I find it?

If you look at my signature you will see the links to my big-mill and mini-mill builds and operations. The guy with the ponytail is my neighbor so he get's his picture taken a lot.

Good luck on your build and let us all know if you need help.

jerry-
 
First off I want to say impressive work as always. In the back and forth discusion between you and BobL on the deflector, another idea popped into my head so I'll throw it out here for thoughts. If you live in farm country, belting that goes into round bailers looks like it would also work for a strong yet flexable deflector guard and I know vibration won't hurt that stuff for a long time. It is sold locally by the foot at Tractor Supply or other farm supply stores.
 
First off I want to say impressive work as always. In the back and forth discusion between you and BobL on the deflector, another idea popped into my head so I'll throw it out here for thoughts. If you live in farm country, belting that goes into round bailers looks like it would also work for a strong yet flexable deflector guard and I know vibration won't hurt that stuff for a long time. It is sold locally by the foot at Tractor Supply or other farm supply stores.

Cowboy,

Haven't seen the material you have described, but don't see why it wouldn't work as a dust/chip deflector. The material I'm using is very similar to that you would have on a plastic full face shield. If what you have described has similar properties, it should work fine.

jerry-
 

Latest posts

Back
Top