Smaller cc Poulan pics please!

[redfin]

2.0 is running well now and just picked up this Poulan today.

 

[Guido Salvage]

Got this one today.

 

[Guido Salvage]

A little bigger, but just as dirty.

 

[redfin]

I need some Poulan 2300 help. When I went to the gentlmans house to look at the saw I posted above I could see the fuel line was torn where it enters the carb housing. I shot some mix in the intake and it fired.

Today I tore it down to replace the line and noticed the cylinder was not tight to the case. Kind of caught me off thinking it would not have fired before with it like this. I figured I would check the squish and just delete the base gasket. I ended up with .28" of squish. I'm asking because this is the first time I have tried without a gasket. Does .28" sound correct for this saw?

 

[Kneet]

Mine has .23", measured from the raised band inside the top of the cylinder. I sanded down the cylinder on a plate of glass with sanding paper and deleted the base gasket.
It's safe and there is some free power when you leave the base gasket out.
I also removed the spark screen from the muffler. It's a good runner now!

Verstuurd vanaf mijn GT-I9505 met Tapatalk

 

[ILikesEmGreen]

I def neef to acquire myself a small cc poulan as well... Cutting up 2-4" limbs with a 3400 can get a bit "cumbersome"

Sent from my C811 4G using Tapatalk

 

[redfin]

Got the above pictured running fairly well. Would anyone happen to know the max rpm on these guys. I have been trying to train my ears but I still like check with the tach

 

[Wood Doctor]

Here's a Craftsman made by Pouilan that I worked on last year:




Medium-sized, about 62 cc, it runs perfectly today. I have in my artillery a 42cc Craftsman/Poulan that also runs flawlessly after I installed a custom-made, typical tension adjuster. An 18" Echo bar fit it perfectly. It weighs about the same as my Stihl 025 and is only a tad heavier than my Stihl MS210C. A good limbing saw, it refuses to die.

 

[redfin]

Got the above pictured running fairly well. Would anyone happen to know the max rpm on these guys. I have been trying to train my ears but I still like check with the tach

My 2300 is still 4stroking in cut at 11800. The below link says 7500 max and I'm way over that?

http://www.acresinternet.com/cscc.n...9f9dec24bc41298688256d62001d965c?OpenDocument

 

[Kneet]

My 2300 is still 4stroking in cut at 11800. The below link says 7500 max and I'm way over that?

That sounds more like WOT, I thought mine does around 11.500 WOT....



Verstuurd vanaf mijn GT-I9505 met Tapatalk

 

[redfin]

Yes at wot its 11800. Sorry I should have written more clearly.

 

[Kneet]

Sounds OK to me.

Verstuurd vanaf mijn GT-I9505 met Tapatalk

 

[stubnail67]

I know where there are 1800's, 2000's and S25's new in the box...

dude you have an s25 new?????

 

[stubnail67]

View attachment 345505

Verstuurd vanaf mijn GT-I9505 met Tapatalk

thats just hott!!!!

 

[stubnail67]

my lil poulans

 

[Guido Salvage]

dude you have an s25 new?????

No, but I know where a couple are.

 

[stubnail67]

i saw one.....dave 76 got it on the bay for like a hundred bux....about 10 minutes before i did a search..... and i know joe 25da has a mint micro also i saw pics of.....i almost got a micro 2300 locally... but by the time i got off work it was gone.....

 

[stubnail67]

i was gonna say post the sweet pics of that one....

 

[sledrat]

my lil poulans

Very nice COllection !