Swap meet...

Rugged made
Treestuff
Wesspur
Shop deals on ebay
Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
litefoot said:
I picked up an 044 project saw. Piston is scored. Cylinder looks like it is salvageable. It has spark. Plastic is not cracked, but it is faded. Trade for good condition 25-28" Stihl bar/chain combo (3/8 .050).
Click to expand...

I have a 28'' Stihl ES bar that has only had one tank and a stihl chain. PM me if interested
 
litefoot said:
I picked up an 044 project saw. Piston is scored. Cylinder looks like it is salvageable. It has spark. Plastic is not cracked, but it is faded. Trade for good condition 25-28" Stihl bar/chain combo (3/8 .050).
Click to expand...

epicklein22 said:
Litefoot, I got a nice stihl bar (near new) and chain (new) combo if you don't go with Brad.
Click to expand...

ms460woodchuck said:
I have a 28'' Stihl ES bar that has only had one tank and a stihl chain. PM me if interested
Click to expand...

And so the feeding frenzy continues:)
 
Looking to deal on a P65 HI-PO that I do not need. I already have 2 big saws.
I only cut 2 16'' cookies with it because I have no logs to cut right now and the saw ran great. However the clutchis bad, the chainkeeps spinning at idle.cap takes a pair of pliers to get it off because the plastic threads are crossed a little, It still tightens good though and the gas tank threads look like new, just needs a new cap. I have a 24'' windsor speed tip that says poulan and a 36'' GB hard tip both bars have chains and are in decent shape. ONE will leave with it. The on and off switch does'nt work have to choke it to shut it off and the recoil hangs out a couple of inches until it starts probably just needs the spring tighten. I know this saw needs a few things but people that have been around these sawswill agree that they are strong runners. I have tried to tell everything wrong with this saw that I know I just got it from a guy that said it needed a clutch. I am looking to for a good running 65-75cc pro saw or? PM me if interested. I did not compression test it but I can tell you that you have to push the decomp to start it, its got compression!
<a href="http://s493.photobucket.com/albums/rr293/ms460woodchuck/?action=view&current=saws012.jpg" target="_blank"><img src="http://i493.photobucket.com/albums/rr293/ms460woodchuck/saws012.jpg" border="0" alt="Photobucket"></a>:monkey:
 
Last edited:
Here's another one of the poulan/pioneer
<a href="http://s493.photobucket.com/albums/rr293/ms460woodchuck/?action=view&current=saws013.jpg" target="_blank"><img src="http://i493.photobucket.com/albums/rr293/ms460woodchuck/saws013.jpg" border="0" alt="Photobucket"></a>
 
I have a 42'' windsor duratip(hard tip) that has only been used once. The chain is stihl .404 chisle. Trade for ????? It is a huskie mount.
 
Wanted:
Stihl small mount bars 24" or 28", 3/8 .050 only
muffler for a Stihl lightning
lots of 064 parts, part saws, or project saws
fairly new 200T

Have for trade:
smashed 200T
18" Stihl mount Windsor Speed Tip bar (66 link) - new
18" Stihl rollomatic ES bar (66 link) - used very very little
18" Windsor Speed Tip bar - new, I forget what it fits, but I posted about it earlier in this thread
20" Stihl Rollomoatic E bar (72 link) - used a little
20" GB Titanium bar (72 link) - used
numerous 3/8 .050 chains in various conditions
3/4 wrap handlebar for MS361, U.S. Handlebar brand I think, used very little
1997 Jonsered 2065, complete saw, runs great, some cosmetic issues

pm me, I don't pay as much attention to this thread as I should.
 
ms460woodchuck said:
Looking to deal on a P65 HI-PO that I do not need. I already have 2 big saws.
I only cut 2 16'' cookies with it because I have no logs to cut right now and the saw ran great. However the clutchis bad, the chainkeeps spinning at idle.cap takes a pair of pliers to get it off because the plastic threads are crossed a little, It still tightens good though and the gas tank threads look like new, just needs a new cap. I have a 24'' windsor speed tip that says poulan and a 36'' GB hard tip both bars have chains and are in decent shape. ONE will leave with it. The on and off switch does'nt work have to choke it to shut it off and the recoil hangs out a couple of inches until it starts probably just needs the spring tighten. I know this saw needs a few things but people that have been around these sawswill agree that they are strong runners. I have tried to tell everything wrong with this saw that I know I just got it from a guy that said it needed a clutch. I am looking to for a good running 65-75cc pro saw or? PM me if interested. I did not compression test it but I can tell you that you have to push the decomp to start it, its got compression!
Click to expand...

Any interest in an 038 Super?
 
Old Homelite and Stihl 075

I have a old Homelite(runs)










attachment.php




attachment.php


plus I have a Stihl 075, 36" bar (I haven't run it in a while)

I need a 20" bar for Stihl 3/8 .050

also looking for a 60-70cc Stihl or Husky
 
Need the following 357/359 parts (tree fall) (not me)

Tank/Handle
Top cover
Recoil assy
Clutch and sprocket (OK, I robbed that one)


Have to trade

Some 371 parts (no top ends)
365 parts (no good cranks, and very little plastic)
038 parts, one NIB tecomec 50mm P+C
1127 Stihl parts
261 parts (no cylinders)
 
Could use an 034 0r 036 muffler. I have the front cover (034), but the back is missing. Also looking for a clutch cover for my 028.
 

Similar threads

V
Lots of Questions about Axe Hanging
Replies
3
Views
1K
thomasinvancouver
T
J
Hello!
Replies
9
Views
1K
jackrabbit
J
HumBurner
Sold 181/281 Parts Saws and various NEW parts
2 3
Replies
44
Views
5K
davidwyby
davidwyby
Whiskey_Bravo
What tests would you want to see on a battery powered top handle saw?
2
Replies
33
Views
3K
Dcsco
D
R
New Saw suggestions
Replies
16
Views
1K
ReddTigger
R

Latest posts

Back
Top