What's on you're bench? 06/14/2013

[blsnelling]

Last night:
I finally unloaded the truck from last weekend's GTG and blew them all off.
Modded a MS440 muffler
Modded a MS660 muffler
Modded a MS441 muffler
Modded a 545 muffler
Modded the muffler, advanced the ignition, and tuned a MS261
Put a 75cc topend on my 2171
Replaced the fuel pump on my mower
Boxed up and labeled 4 packages to ship
Cleaned Anna's aquarium and changed the water

Next in the list:
Port a MS261
Port another MS261
Port a 390XP

 

[barneyrb]

Well I think this is going to get torn down, port mapping done, parts ordered, and then start the assembly process. If I don't get started now I WILL NOT be finished by late September...

 

[steve316]

Why what are you going to do this afternoon. Steve

 

[NewToStihl]

LAST NIGHT:
- 'played' with a MS261 that Brad modded
- completed assembly, tuned, tested, cleaned & photographed MS660 to go on ebay
- Cleaned carb on a POS Poulan handheld blower a friend asked to me to 'look at'


NEXT ON THE LIST:
- start evaluating & working on FS90R & FS110X trimmers I acquired (don't like working on trimmers!)
- press/vac test early version 041AV that cuts out when inverted
- change brake fluid in truck
- change ATF fluid & filter in truck

 

[barneyrb]

LAST NIGHT:
- 'played' with a MS261 that Brad modded
- completed assembly, tuned, tested, cleaned & photographed MS660 to go on ebay
- Cleaned carb on a POS Poulan handheld blower a friend asked to me to 'look at'


NEXT ON THE LIST:
- start evaluating & working on FS90R & FS110X trimmers I acquired (don't like working on trimmers!)
- press/vac test early version 041AV that cuts out when inverted
- change brake fluid in truck
- change ATF fluid & filter in truck

I want pictures of your bench if it will hold a truck......

:hmm3grin2orange::hmm3grin2orange::hmm3grin2orange:

 

[TheJollyLogger]

Two more of my buddies 338xpt's, of course. Fuel lines and crab kits, and 1 oiler. Still can't believe ya have to tear it down to the crank just to replace the oiler.

 

[TK]

Took a completely assembled saw and turned it into a box of parts. Then probably 6 months from now after cleaning all the parts, I'm going to see if I can reassemble it as fast as it came apart :msp_w00t:

 

[NewToStihl]

I want pictures of your bench if it will hold a truck......

:hmm3grin2orange::hmm3grin2orange::hmm3grin2orange:

It's a first gen. Tacoma . . . very small truck . . . probably isn't much bigger than the mower Brad apparently has on his bench. :msp_wink:

 

[Modifiedmark]

Just took my Husqvarna 2100 off the bench last night. It was smoking like a freight train last weekend for the GTG burning bar oil. I replaced both crank seals and it seems better, still smoking some even after running it a bit, but not like it was.

Got a Poulan 3700 up next and I'm still looking for presets for the 1/2" Mac chain so I can try the Long straight bar on the Poulan S72.

 

[tallfarmboy]

Trying to get everything buttoned up and finished on this 090. I must have lost the large clutch washer somewhere... I don't know where, but that is what I am waiting for. I've got an 066 that will be on deck, then a Roper D44, and finally a McCulloch 2-10PS.
Need to find some decals for the 090, but the paint turned out much better than I expected.
View attachment 300070
There is a picture with everything just sitting on it... Not done.
And a video of the first time I got it running.
[video=youtube_share;CsWNo0vGfEs]http://youtu.be/CsWNo0vGfEs[/video]

 

[andydodgegeek]

I have my dads old l77 husky apart to replace crank seals. Then I have a husky 36 that my brother bought at a garage sale for $7 that I am going to tear apart and try a little grinding inside of. Along with all sorts of bigger projects like replace deck on Skidsteer trailer, r&r transmission in my motorhome, cut/split/fill woodshed, fish, and I would like to build another tuned pipe for one of my saws.

 

[7hpjim]

Two more of my buddies 338xpt's, of course. Fuel lines and crab kits, and 1 oiler. Still can't believe ya have to tear it down to the crank just to replace the oiler.

I have a 335 top handle, the case has a hairline crack @ the front near the trigger and is it normal for these to go to the off position on the master control when the throttle trigger is squeezed past WOT??

 

[BloodOnTheIce]

Turned a HT131 pole saw with a bent shaft into a HT130 with a brand new short shaft.

 

[Stihlofadeal64]

lots of junk at the moment. Several project saws around. Tried to do a bit on it yesterday - no workee.

I banged muh toe last week and have been hobbling around like Festus...don't laff it may happen to you soon. I forgot how bad this little toe can hurt! :bang:

 

[7oaks]

Trying to get everything buttoned up and finished on this 090. I must have lost the large clutch washer somewhere... I don't know where, but that is what I am waiting for. I've got an 066 that will be on deck, then a Roper D44, and finally a McCulloch 2-10PS.
Need to find some decals for the 090, but the paint turned out much better than I expected.
View attachment 300070
There is a picture with everything just sitting on it... Not done.
And a video of the first time I got it running.
[video=youtube_share;CsWNo0vGfEs]http://youtu.be/CsWNo0vGfEs[/video]

WOW - looking sharp and sounds good.

 

[Stihlalltheway]

Dropped off the 044/6 hybrid to get pressure/vac tested and now it's time to retune my 028 then watch some tv.

 

[H 2 H]

5 chains that need re-sharping

But it's race day so getting my camera gear ready - just waiting for the batteries to recharge

 

[o8f150]

nothing on the bench except a big box of parts where i parted out about 20 weedeaters,,, have to service the mower

 

[old 040]

just got done mounting up a new high top filter kit on my newly acquired 288xp, did an 272xp top end swap on my early 61 a couple days ago, and i threw in a pic of my vintage suzuki tm 125 that i restored a few years back, i need to replace a kick stater gear set in it, so it will be on the bench soon..................View attachment 300103View attachment 300104......................

 

[mdavlee]

395 waiting to be ported and a few chains to sharpen. With working 6 days a week and not much time in the evening I'm going very slow on it. :msp_mellow: I usually want to get it done as quick as possible but it's been on the bench since saturday and not been touched.