Yall think she will hold up tommorow?

[Jkstihl]

Yall think she will hold together tmw? Dont have a back up rim gonna send it i reckon.

And shoutout to @Yotaismygame for the 25" and chain.

 

[mkinslow]

I wouldn't run it, if it lets go at load its possibly gonna mess up quite a few things around it.

Sent from my SM-G892A using Tapatalk

 

[Justin Taylor]

This is why I always Carry a extra rim with me and it will probably be fine just keep that chain sharp

 

[timbrjackrussel]

Sharpen the chain. Rim is junk. Put the new one on so that the chip ejector holes are on the outside.

 

[Justin Taylor]

Sharpen the chain. Rim is junk. Put the new one on so that the chip ejector holes are on the outside.

Did you even read the post?

 

[timbrjackrussel]

I always have extra clutch, bearing, rim, washer and E clip with me. 066 Arctic.

 

[Brent Nowell]

With the clutch cover on I think that the chain will guide nice into the rim if it’s properly tightened. IMO with a loose chain you might have a lock up, which could be really bad if you stuck in heavy wood.

your call of course but I say send it for the day If you have to, don’t push it for a second or third tho

 

[Huskybill]

Looks like a pit stop at the dealer in the morning.

I replace the sprockets with rim/drum and save the sprockets in the beginning.

I stock in-house new rims, drums, clutches, bars, chains, air filters, recoil springs, spark plugs and starter ropes. I do inspect the rims often.

Any break down I can fix overnight. With the dirtbikes if we lost an engine at 7 pm by 12am she was bored, new piston, crank seals and bearings ready to ride the next day.

 

[Ketchup]

I snapped a 42” chain on a 395 once. It whipped up my arm, hooked on my shoulder and pulled me backwards. Luckily I had on a thick jacket. I was fine, just a little cut on my wrist. It had been making a weird sound in the cut. When I looked the saw over I discover two pieces of sprocket still jammed behind the clutch drum. The chain catcher was sawn
completely in half.

That sprocket might wreck more than your saw. Might wreck you too.

 

[svk]

I wouldn’t run that

 

[Jkstihl]

I wouldn’t run that

Yeah thats kind of the way im starting to feel about it...

Dont think i will.

I can envision bad **** happening.

 

[Justin Taylor]

Yeah thats kind of the way im starting to feel about it...

Dont think i will.

I can envision bad **** happening.

If a dealer is within 30 min then yes go get a new one

 

[cuinrearview]

Chain and rim are unusable in the state they're in.

 

[Evan]

I'd send alot of **** but to be honest I dont know that I'd run that.
I ran my 026 for a few hours with no clip holding the sprocket on. It came off 3 times while doing a paying small tree removal job. Nothing bad happened and the tree ws removed.

 

[holeycow]

not a chance. what could possibly be the point of running that ****.

 

[Mad Professor]

Get a few extra rims when you go to the dealer. I keep 7T and 8T 3/8, 7T 3/8 picco medium spline, and 0.325 and 3/8 small spline. If I put on a new chain , I'll have a rim handy if needed, or I want to change pitch or # of teeth/bar

Running that setup is stupid and dangerous.

 

[Jkstihl]

Well it was still too wet this morning, but i had already decided not to run it anyway.

I dont know how long it was broke before i switched bars, anywhere between 1 day to 3 weeks.

After inspecting i do need a clutch drum, it seems to be slightly warped. I think that is why i have been having chain creep.