I have an MS362 that the previous owner was running with a .325 pitch, 20" bar setup. I would like to get a new bar for it, and because I already have the necessary 3/8 sprocket and I also have one of Stihl's 2in1 sharpeners/file guide for 3/8 chains, I am thinking why not switch back to a 3/8 setup? That is how the 362 comes from the factory, no? I have no complaints about it's current performance, but I am curious what I might notice (good, bad, or otherwise) if I change the chain pitch. Thanks!
Switching a Stihl MS362 from .325 back to 3/8 pitch. Good call?
- Thread starter T.Bird
- Start date
Help Support Arborist Forum:
No reason not to go 3/8.
This is kinda what I was assuming.Theoretically the narrower .325 would cut a little faster due to the narrower kerf. And a little smoother due to the narrower spacing between the teeth. But there's nothing wrong with 3/8. It might be interesting to run both side by side.
I prefer 3/8 for actual firewooding and general wood cutting. I have .325 on a fencerow----trim saw that is 50cc.
A 60cc can easily pull that 3/8 with a 20 in bar.
A 60cc can easily pull that 3/8 with a 20 in bar.
How was this done as the 362 has large diameter splines? Run a 9 pin rim sprocket?
I think it is standard and mini spline for Stihl and standard and small spline for others. I don't have one but read on here the 036 or some of them have a mini spline drum that will fit. If you have to go to 9 tooth drive to do .325 that would be worse than 3/8 7 tooth for most use.
Yeah, I was looking at running .325 on my 362C but there didn’t seem to be an obvious way. I went with a new 3/8 bar and kept it the same.
Oh! That's really interesting. Maybe it IS a 9 tooth drive. I'll have to check this afternoon.
I think you might be a little misinformed the 325 is the pitch the drivers are probably 050 or 063 this is my guess
Everybody reinventing the wheel.
Run 3/8 on a 60cc saw. With an 18 or 20". Done.
Or..., do whatever the heck you want
Run 3/8 on a 60cc saw. With an 18 or 20". Done.
Or..., do whatever the heck you want
If I ran my Stihl MS361 on .325" pitch chain she would probably feel insulted and say, "Hey guy, I am not an 026 or even an 028. Let me show you what I can do with the recommended chain pitch -- 3/8". Got it?"
spuldup
ArboristSite Operative
3/8 on this size is appropriate. .325 is under-loaded, even when sharp.
You've got a strong 60cc chainsaw, it's not a jigsaw. (over dramatic but that's the point)
You've got a strong 60cc chainsaw, it's not a jigsaw. (over dramatic but that's the point)
I have a 9 pin .325 large spline rim from Stihl. I got it for my MS441. If I remember right it is similar size to an 8 pin 3/8. If they made an 8pin .325 rim in the large spline I would have one. I have 8pin .325 in mini and standard spline.
Run what works for you. The saws came from the distributor with either chain. If it is sharp. it cuts well.
But, the .325 setup is a rarity anymore. 3/8 square tooth (RS) chain territory.
But, the .325 setup is a rarity anymore. 3/8 square tooth (RS) chain territory.
Look here the husqvarna 560 comes with 0.325 pitch 0.058" or 1.3mm gauge chain. https://www.husqvarna.com/uk/chainsaws/560xp/Everybody reinventing the wheel.
Run 3/8 on a 60cc saw. With an 18 or 20". Done.
Or..., do whatever the heck you want
Not if the gauge is 063
325 9 pin large 7 spline 22mm hub
I've ran the 20" 325 050 on my 660 and other saws for testing. 325 is smoother in limbs under 6". No other gains are there. 20" isn't worth worrying about chain pitch.
The only kerf advantage to 325 is NK 050. I run it on my 16" 435 Husky big box store saw. They came with that chain stock.
Yeah I don’t want or need a 9 pin rim on a working saw.
Similar threads
Latest posts
-
-
-
New to Chainsaws / Storm Clean-up / Husqvarna 435, Echo CS-3510, CS-4010, other?- Latest: Breckinridge Elkins
-
-
-
-
-