Oh, my bad. Should start getting warm by then.
Steve
Steve
Nik's Poulan Thread
- Thread starter FATGUY
- Start date
Help Support Arborist Forum:
Dang my back is hurting working on these 2 today. Carry to log and back etc. 
Like carrying a Mac PM605, concrete block with bar.
Steve
Steve
Hahahaha some chubby girls are pretty too but not them 600 series poor things. I've got 1 that runs well but always find something I'd rather work on instead so it just sits
I know this is supposed to go in the wanted section, but I need a good used 4200 crankshaft if anyone has a spare.
Bought a clean/washed saw last year & when I opened it up this weekend the big end was all rusted & both main bearings too. He probably didn’t cover the air filter during a power wash & that carb points straight down into the case...can’t fix stupid.
The 5200 uses the same one.
Bought a clean/washed saw last year & when I opened it up this weekend the big end was all rusted & both main bearings too. He probably didn’t cover the air filter during a power wash & that carb points straight down into the case...can’t fix stupid.
The 5200 uses the same one.
Is a 5400 the same
Good question, I’ll compare the two IPLs.
EDIT-
They are all the same, 530022113
EDIT-
They are all the same, 530022113
Man, that stinks. He could have at least blown it out and fogged it real good with oil.
Steve
Steve
This is our section, post away. Everyone helps everyone.
Steve
Steve
I don’t know how to link but search,ebay ,poulan 5200 crankshaft, , down aways is a add has 10 new 18.95 it's customchainsawparts
Search poulan 5400 crankshaft and it's top
What a nice post you guys are great
IMO best to ask for wanted parts in the brand boards your wanting the parts for just like you did. I do it too, buy and sell that way. IMO best way. You did right thing in my book.
If someone gets offended by it IMHO they can get
If someone gets offended by it IMHO they can get
I asked for some measurements for a full wrap handle in one of the forms with red saws a while back and bumped it twice and still no answer. If I had asked in this forum I would have had answers stacked up before the day was done. That's the way it should be so thanks to all for your help to each other
I saw that Todd. You fella's in here definitely do your darndest to help someone out and feel welcome. I have a red saw with an issue too and no real point in asking there unfortunately. Perhaps I should put a poulan sticker on it and ask here haha.
Have you got a 390 and need a full wrap or are you seeing if it could fit another saw? My mate has one but it's a half wrap
I was looking at a husqvarna full wrap handle on flebay and just wanted to get the size. Though I could make it fit by cutting the brace bar and making any changes required then reweld it. They are only about 40 to 50 bucks. I went to the dealer but they didn't have any full wraps. I will get it figured out sometime
A poulan full wrap handle is 13 wide outside and 11 1/2 tall outside. That is what I am trying for
Ahh right I new you must of had a plan for it. I've got a little 350 and its behaving like it has a limited coil but only just above idle. It makes induction noise as the throttle is opened but will not rev at all. Silly as it will run great for ages then you go start it again and it does that are any of the plastic poulans part of that family?
All, I think the Poulan Thread started by Nick (AKA FATGUY) years ago is one of, if not the best on AS. I have saws from many manufacturers in several cc sizes and have to admit I was/am a Homelite junkie before seeing "the light" with Poulans! They're just so FUN to work on! I have to say I wouldn't have the collection I do without everyone's help and hospitality here on the Poulan Thread and hope to one day be able to repay the favors given me by others. Bob Redunshee , Stephen Acorn Hill, Gary Guido Salvage to name just a few for parts and such, and too many to list for advice and counsel. Thanks guys, let's keep it up! Max.
I had a 385 390 full wrap but never measured anything like that before selling. Think one of my locals runs a 395 394 full wrap. I will try and remember to check it when in.
PM what measurements so I know what to check.
PM what measurements so I know what to check.
Similar threads
