Pictures of the carb off of the Buz, kinda hard to get a good picture....
Swap meet...
- Thread starter Four Paws
- Start date
Help Support Arborist Forum:
firefighter33
ArboristSite Guru
Look waht i found today
Looks to be in good condition has good compression. Just not my thing anyone have any interest??? Looks BAD A**!
firefighter33
ArboristSite Guru
Thats good looking to trade not sell. Not sure what u got. Im up for anything a little newer.
i found out that the the poulan micro xxv is a poulan micro 25 xxv and i got everything exsept the carb and filter for it. and i don't need the clutch nomore i found one from a buddy on here.so if anyone needs any parts for a poulan micro 25 xxv saw i got everything exsept the carb and air filter just give me a hollar
Eccentric
Mister Wizard
Hey Mitch,
Do you have any low-profile McCulloch application HL's to part with? Should be HL19-something or HL63-something. I could use a few, especialy if they're from McCulloch 200/250/300/380 type saws with the non-governor type throttle linkage.
whah !!!!!!!!!!!!!!!!!!!!
i brokened it ! C5 starter cup,dont know how.
any body got a starter cup to fit a homie C5 ??
gave my spare away
Eek. That's why I haven't given away the spare cup or two that I have now. I know I'd need it right afterwards. Damn FM starters....
Nice looking "watering can" bevel-drive McCulloch. Is that a 33 or a 35? I'll bet that'd be a runner. They go forever. Only think that sidelines them is the expensive and hard to find carb diaphragm. Last one I saw on feebay was listed for $50! I'm still on the lookout for a reasonably priced diaphragm for mine.
As for your Buz..........I'm wondering why don't you just run the original Tillotson HC? If that HC is now crap (but you still have it) then you should be able to swap the throttle shaft/arm assembly from it into the HL you're running.
I wonder if the linkage setup on an HC from a Mono (like my Wards WD60) or a McCulloch 15 is the same as yours.
sefh3
Addicted to ArboristSite
whah !!!!!!!!!!!!!!!!!!!!
i brokened it ! C5 starter cup,dont know how.
any body got a starter cup to fit a homie C5 ??
gave my spare away
Post a pic of what yours looks like. I have a few cup laying around but not sure what they came off.
firefighter33
ArboristSite Guru
smilin possum
Addicted to ArboristSite
I sure would like to find a 78 drive link loop of 9/16 for my DA-211 Mercury.
Got green backs.
Got green backs.
roncoinc
Official Stihl Disser
The fairbanks morse starter setup was used on a lot of early saws.
look "inside" the cup and if you see wear marks where the pawls grabbed, it will probly be the one.
If i brave the cold today will go down and measure and take a pic,supposed to look for stuff anyway.
tnx.
roncoinc
Official Stihl Disser
Took a pic.
also checked a wright i had,diff looking but same size,so i think many will work.
look at the inside and you can see he scrape marks by the pawls.
oldsaw
"Been There, Milled That"
Need all the intake bits for a Husky 272. Intake, AF holder, choke lever. Have carb, but will buy the whole assembly if needed since not sure how good carb I have is.
PM me.
PM me.
Duke Thieroff
Fill your hands, you SOB!
Have a MS180c up for trade and an 011av up for trade. Got them from a member here(Hey Doug, thank you) basically entertaining offers for bigger bore saws, for firewood cutting, let me know what you have.
The 180 will need fuels lines and possibly a carb kit, will start, could benefit from a muffler mod, I'm sure.
I haven't really got into the 011av but it definately has compression. Will need a clutch cover for sure. I will look at it more tommorow if anyone has any questions.
CT
The 180 will need fuels lines and possibly a carb kit, will start, could benefit from a muffler mod, I'm sure.
I haven't really got into the 011av but it definately has compression. Will need a clutch cover for sure. I will look at it more tommorow if anyone has any questions.
CT
Last edited:
Have a MS180c up for trade and an 011av up for trade. Got them from a member here(Hey Doug, thank you) basically entertaining offers for bigger bore saws, for firewood cutting, let me know what you have.
The 180 will need fuels lines and possibly a carb kit, will start, could benefit from a muffler mod, I'm sure.
I haven't really got into the 011av but it definately has compression. Will need a clutch cover for sure. I will look at it more tommorow if anyone has any questions.
CT
I have a complete 2-10, she ran some I give up on getting that carb to work, Ill trade ya for the 180 its completely clean you wont have to clean it at all.,.
TRI955
I'm the man in the box
PM sent
firefighter33
ArboristSite Guru
Looks to be in good condition has good compression. Just not my thing anyone have any interest??? Looks BAD A**!
Nobody is interested in this fine machine? Will take project or runners for trade!!
Mastermind
Work Saw Specialist
I would like to have it. The 1-70 I have is lonely for another Mac. What kind of saw did you have in mind? Just something newer?
firefighter33
ArboristSite Guru
Yeah im up for whatever. This is just a little old for me. What u got?
