Swap meet...

[rms61moparman]

Hey Guys,

I need a blown up Husky 142 or similar.
A buddy of mine loaned out his 142 (that I went through and ported) and it came back with the muffler loose and a hole melted through the oil tank.

I may have to try to patch the tank but if someone has a good one laying around...?
Not a lot of $$$ to spend but might do some trading.


Mike

 

[sefh3]

Homelite Bar

I have a 28" Homelite bar and chain. Interested in Stihl stuff. PM with what you have.

 

[7hpjim]

I would like to find a 272 project saw, got the 268 going and ended up with an xtra good 272 top end and carb and would like to use it, also need inner dawg and a good clutch cover foe a Partner R440T, have green to trade.
Jim

 

[Modifiedmark]

Still looking for a decent fuel cap for a Echo CS-302S and a Poulan bow setup.

 

[TRI955]

I would like to find a 272 project saw, got the 268 going and ended up with an xtra good 272 top end and carb and would like to use it, also need inner dawg and a good clutch cover foe a Partner R440T, have green to trade.
Jim

I have a 272 sitting here, missing carb, intake, and all covers. PM me if interested.

 

[my82cam]

does anyone have a crankcase for a stihl 025 or 021? mine got melted behind the clutch and the oil pump now leaks a ton of oil. lol

 

[dh1984]

i might have one here someplace for an 021 pm sent

 

[little possum]

Looking for a oil pump for a Pro Mac 700.

Couple parts, and a couple of frog eye$

 

[firefighter33]

Looking for a 044,046 project anyone have one they would part with? Have some stuff to trade or cash!

 

[CM76]

Hi,

I am looking for parts for the Pioneer 850 geardrive saws. Anything and everything, as my project saw is pretty lean on original components!!!

Regards,

Chris.

 

[Jordan3605]

looking for homelite super 2 s
parts or complete
message with details

 

[Madsaw]

looking for homelite super 2 s
parts or complete
message with details

I can see how many I have of them. What do you need?
Bob

 

[plumbcrazyjr]

i have a stihl 088 project saw that i want to swap for something
it is complete and turns over but acts like it is hitting something. the parts are to expensive for me so i will let it go to someone else to mess with pics can be emailed
Thanks
Eric

 

[nautilus]

Pm sent

i have a stihl 088 project saw that i want to swap for something
it is complete and turns over but acts like it is hitting something. the parts are to expensive for me so i will let it go to someone else to mess with pics can be emailed
Thanks
Eric

 

[my82cam]

i think i found my 025 case, thanks guys!

 

[7hpjim]

I have a 272 sitting here, missing carb, intake, and all covers. PM me if interested.

thanks for offer, need covers too, got mine with intention of using top end on the 268 but saved the cylinder and running a meteor piston, the 272 has a broken case on the starter side but had a good cylinder missing top cover, recoil, clutch cover,outer dawg, most of A/F assembly

 

[huskydude]

Hey Guys,

I need a blown up Husky 142 or similar.
A buddy of mine loaned out his 142 (that I went through and ported) and it came back with the muffler loose and a hole melted through the oil tank.

I may have to try to patch the tank but if someone has a good one laying around...?
Not a lot of $$$ to spend but might do some trading.


Mike

PM roncoinc. He has a couple.

 

[o8f150]

looking for a 16" bar for my 024,,50 gauge,,325 pitch,,,,,, i have a 18" bar,,325 pitch i believe it is 58 gauge,, this bar came off the 024 that i will trade,,,its in good shape and straight

 

[longbar]

Anyone have a Poulan 8500,5200,5400 parts saw I need the coil, starter, bolts and carb and other misc parts for an 8500.

or a 2054 parts saw I need the recoil, carb and some other misc parts.

I have 045/056 parts, 025, another stihl clamshell not sure what it is yet with a good jug and slug. Also tons of hommie 330/360 parts and poulan 3400, Mac pm605/610 parts and alot of mid size olympk parts 264/254 and others around that size. Also johnnie 2045 parts and other stuff.

Also looking for a Johnnie 2094/5

 

[o8f150]

looking for a 16" bar for my 024,,50 gauge,,325 pitch,,,,,, i have a 18" bar,,325 pitch i believe it is 58 gauge,, this bar came off the 024 that i will trade,,,its in good shape and straight

ok,,everything i checked on the 18" bar it is a 63 gauge and they don't make a 50 gauge for this saw,,all i can find is 63 gauge