3120xp

[tgerloff92]

Ordered it so hopefully it'll be here in a week or two. What have you guys paid for them?? PHO it was almost 1700. I ordered it thinking I've read better things about it than the 880. So I call my dealer to just see what the 880 wrap went for. 1639 with a 36" bar! And I think it was 1749 or so with a 59" bar. Really wishing I hadn't ordered that husky, but I do like that its the sane bar mount as my others so I can use some bars I have for my 395.

 

[blsnelling]

$1700 PHO? I haven't priced one, but that sounds high.

 

[tgerloff92]

And he said that was 10% off! It goes through our little local ace store. I have to special order any husky's there but they don't service or stalk any parts for saws. Next one is a Murdochs two hours away where my Stihl dealer is located. So usually I just go Stihl due to better PR and parts availability. But geez I feel like I got hammered after I called Ken about the 880

 

[EXCALIBER]

I asked a dealer in Colorado about the 880 or the 3120 XP, he clearly said the 3120 was better. Just for a note, he sells echo, husky, and stihl for saws. Although i was going to use it for milling. I personally much prefer the switches on the husky saws as compared to the stihl. The air filtration is also better on the husky, good choice IMO

 

[o8f150]

$1700 PHO? I haven't priced one, but that sounds high.

1800 on huskies web sight

 

[Joe Kidd]

Kudos! Makes my back hurt thinking about running the big dawg! :msp_thumbup:

 

[mdavlee]

I've seen them for $1400 or so pho brand new sitting on a shelf at a dealer.

 

[tgerloff92]

1800 on huskies web sight

But is it worth ALL the extra money?? That's a lot of money in bar and chain!

 

[WidowMaker1]

great saw!!! you paid less than we do in OZ, but then we get 12k coils, and 1.20 H-jet ....well my saw did anyway. beast of a saw for Big ****! not a weiner's saw

 

[Mastermind]

Cinder block wit handles......

:hmm3grin2orange:

 

[mdavlee]

Cinder block wit handles......

:hmm3grin2orange:

But those cinder blocks will really pull a 36" bar with an 8 pin and full comp like nothing.:msp_tongue:

 

[Mastermind]

I picked this up the other day...

 

[Mastermind]

But those cinder blocks will really pull a 36" bar with an 8 pin and full comp like nothing.:msp_tongue:

Roll tide was running a 9 pin with a 36" on the 395XP I built him at the WKY GTG......till he slung the chain.

 

[jropo]

Cinder block wit handles......

:hmm3grin2orange:

Lead suitcase.:biggrin:













I'm sure they will be all the rage next year.

 

[mdavlee]

Roll tide was running a 9 pin with a 36" on the 395XP I built him at the WKY GTG......till he slung the chain.

That's why I said 8 pin instead of 9. The longer bars just don't have the belly or a wide enough tail on the husky mount saws for a 9 pin. The large mount stihl probably can get away with it.

 

[Mastermind]

That's why I said 8 pin instead of 9. The longer bars just don't have the belly or a wide enough tail on the husky mount saws for a 9 pin. The large mount stihl probably can get away with it.

I agree.

This 084 I just got is set up with 36" .404 I may keep it that way.....

 

[tlandrum]

there seems to be a big hole in my 3120 muffler:hmm3grin2orange: View attachment 260475

 

[mdavlee]

Looks different from the last time I seen that saw.

 

[tgerloff92]

No weenie here! 6'3" 240 and played some college ball. im sure i can handle the lil girl

I told the guy to order it 3/8 so i can run my existing bars on it. but we'll see i looked on Husky's website and im pretty sure they spec a .404 drive. Either way it will prolly get an 8 pin 3/8 either way.

Randy your wife spoils you!

And it'll be getting an unlimited coil and high jet sooner than later.

 

[tlandrum]

its about 50 lbs lighter too :hmm3grin2orange: