What do you keep your bar oil in??
- Thread starter blkcloud
- Start date
Help Support Arborist Forum:
Erik B
ArboristSite Guru
I keep the gallon jugs at home and use them to fill a dish detergent bottle that I use to fill the saws. I only go through maybe a gallon to gallon and a half per year. Only cutting for my own use so my method would not work very well for someone cutting wood for a living.
I have several quart bottles of bar oil that I keep refilling. Strap one to the wheeler when I go cutting. If I'm cutting roadside stuff I just bring the gallon with. Now that I have so many saws the bar oil goes quick.
dwasifar
ArboristSite Operative
I fill a quart bottle from the gallon jug just because the smaller bottle is easier to pour into the saw without spilling. But I like Erik's dish soap bottle idea and I might switch to that.
Why? You can still only be using one saw at a time. Using eight saws for an hour each vs. one saw for eight hours should use about the same amount of oil.
Why? You can still only be using one saw at a time. Using eight saws for an hour each vs. one saw for eight hours should use about the same amount of oil.
Well normally when you buy a used saw it's nearly empty plus a number of my older saws slowly leak oil as they sit.
TimberWolf530
ArboristSite Guru
Looks like I'm the only one here, but I just keep it in the bottle it comes in.
I keep it in the jug it comes in. IMO it's a waste of time to be transferring it to smaller bottles. How much oil does a saws tank hold anyways, 3/4 of a quart? A full days worth of work I could burn about 5 tanks of gas/oil depending what I'm cutting. If I was carrying a 2 quart bottle it wouldn't last the whole day. Might as well just take the jug.
ChoppyChoppy
Tree Freak
I dump the jugs into a 1.5 gal gas can. I find its easier to pour. Usually mix in a cup or two of diesel to thin a bit.
sunfish
Fish Head
My 'ditty' box is a milk carton crate. Contains a 1 gal oil jug, 1.25 gal fuel can, handfull of wedges, scrench. Been at this work in 1976 and the only oil jug that leaked was the one when I ran over the entire box with a load of wood.
greenskeeper
ArboristSite Operative
WMO for me, so I store it in the oil bottles the fresh stuff came in!
Woos31
Addicted to ArboristSite
I also use the same jug it comes in, buy it by the gallons and when one is empty.........it holds saw has real good too, tie jugs together, never forget one or the other
hedge hog
ArboristSite Guru
Been using this for 2 years.
Mine is a flooring sealant and have 2 spare Tide HTE jugs with a plunge valve
They hold a gallon and don't drip when they are shut off
They do pour a little slow at 10 degrees but are very clean to use
Sent from my iPhone using Tapatalk
This is probably a 25 year old bar oil quart bottle that I just keep refilling from the gallon jugs I buy. Fits better in my saw box, easier to get the oil in the saw, and only in the saw.
That's a neat bottle. I wonder if any of the laundry bottle caps like that will screw onto the gallon oil jugs.
Been using this for 2 years.
Mine is a flooring sealant and have 2 spare Tide HTE jugs with a plunge valve
They hold a gallon and don't drip when they are shut off
They do pour a little slow at 10 degrees but are very clean to use
Sent from my iPhone using Tapatalk
kingOFgEEEks
Out, standing in my field.
I use a coffee creamer jug. The lid snaps tight and seems to hold up. This is only when I go 4 wheeler cutting, when I take the truck, the gallon of TSC bar oil is on the floorboards next to me, where the heat can warm it up.
I forgot to mention. The quart bar oil jugs I like best are the tall narrow round ones that look like a gear lube jug but with a standard top. They seem to pour much better than the rectangle ones.
hedge hog
ArboristSite Guru
Maybe on that bottle but I think the laundry soap bottle is thread on. Im going to check when I go home tonight. Might depend which brand it is. Or maybe Im thinking its thread on because I remember threading the other cap on the bottle???
